Determine the reaction/s at each support, given the data and figure below. X 3 kN/m Y 18 kN/m L= 1 m What is the reaction (kN) at the roller support? Type answer in two (2) decimal places only without the unit. Y (kN/m) Y. 5 X (kN/m) (kN/m) 5 kN/m 5 kN/m A C B 10 m L (m)

Determine the reaction/s at each support, given the data and figure below. X 3 kN/m Y 18 kN/m L= 1 m What is the reaction (kN) at the roller support? Type answer in two (2) decimal places only without the unit. Y (kN/m) Y. 5 X (kN/m) (kN/m) 5 kN/m 5 kN/m A C B 10 m L (m)

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.9P

See similar textbooks

Related questions

Q: A post-tensioned prestressed beam of span-length of 10 m has a rectangular section 300 mm wide 800…

A: Area of concrete, AC = 300*800 = 240000 mm2 Area of steel wire, AP = 500 mm2 Initial Force, Po = 250…

Q: 3. A simply supported beam AB of span 6 m is loaded as shown in Fig. 12.14. 2 kN 5 kN 2 kN/m 2 kN/m…

Q: How would we derive a solution for groundwater drawdown due to pumping near a river (i.e. a recharge…

A: Brief concept introduction- Groundwater- It is the water that is stored under the earth's crust.…

Q: The 400mm x 400 mm square concrete column is reinforced by 6 - 25mm diameter steel bars. If the…

Q: An asset that is book-depreciated over a 5-year period by the straight line method has C3 = P…

A: The formula for straight line SL depreciation is as follows : d=(P-S) /n Here, P is initial cost,…

Q: Determine the axial force (kN) in each member of the assembly shown below, Member Cross-Sectional…

A: Given: The modulus of elasticity is 200 GPa. The cross-sectional area of members AB and DB are 1000…

Q: Example: - Compute the main stations of reverse circular horizontal curve, if (Ci=244m, A-42° 36',…

Q: What value of T makes these two cash flow diagrams (see figure) economically equivalent at 15%…

A: Given Annual Interest = 15%

Q: An approach at a signalized intersection with a 75-second cycle gets 26.25 seconds of displayed…

Q: Memo No. Date Mo Tu We Th Fr Sa Su P lialy sis by cs lpe Deflection metud) 5m 3 m 12

A: In given frame Data is insufficient for solving the problem

Q: Jf g is the punching shear resistance per unit area a, is the side of a square footing for a column…

A: Given: Punching shear resistance per unit area(a) = q b = side of square footing column Total weight…

Q: The length of curve at side of PC is 50 while on the PT is 60 m. A sewer line with its t top having…

A: Given: The length of L1 is 50 m. The length of L2 is 60 m. The elevation of the sewer line at…

Q: The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress…

A: This question has been taken from the design of steel structures

Q: 2. The following data describes the existing conditions of a river within a project study area: -…

A: Note: As per our policy only three sub parts of a question can be solved. For other sub parts please…

Q: Design a branch canal of an irrigation system with the data given below using Lacey's approach for…

A: Solution: Given: Q = 4000+50x1 = 4050m3 d = 0.20mm

Q: A consolidated undrained (CU) triaxial compression test is conducted on a normally consolidated clay…

Q: The 400mm x 400 mm square concrete column is reinforced by 6 - 25mm diameter steel bars. If the…

A: Given data in question Cross section Diameter of bar Number of bars Stress Elasticity modulus To…

Q: A pretimed four-timing-stage signal has critical lane group flow rates for the first three timing…

A: Given data: Flow rates of first three timing stages: q1=274 veh/hrq2=114 veh/hrq3=271 veh/hr…

Q: 2- Subsurface geotechnical investigations carried out in a deposit of sand provide standard…

Q: QUESTION: 1.) Determine the best hydraulic section for rectangular channel that can carry 200…

A: Rectangular channel: An open channel with a rectangular cross-section used for the flow of water…

Q: .109 A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown…

Q: A conventional drained triaxial compression

Q: The total stress paths corresponding to different laoding conditions, for a soil specimen under the…

Q: In a wide rectangular channel having a depth y = 1.8 m and unit width discharge q = 1.5 m²/s, an…

A: q = 1.5 m2/s b1 = 6m Q = q *b1 = 1.5*6 = 9m3/s

Q: Give reasons for the following : 1- Adding gradients and reinforcing steel to the individual…

A: Foundation is a structural component used to transfer load from the superstructure to the earth…

Q: The two-dimensional framework consists of two bars CE and CD pinned at C, D and E; and a horizontal…

A: Let T N be the axial force applied on AB to close the gap of distance x.

Q: 1- A machine and its foundation weight 270 kN. The spring constant (for each spring) and the…

Q: A turbine system is harnessing the energy of flowing water from reservoir 1 to reservoir 2. The…

Q: The length of curve at side of PC is 45 while on the PT is 50m. A sewer line with its top having an…

A: given-Length of curves L1=45 m and L2=50 msewer line top elevation = 108.6 msewer line top…

Q: Find the cross sectional dimensions of the smallest square beam that can be loaded as shown in the…

A: Given data Allowable shearing stress (τ) = 1 MPa Allowable bending stress (σ) = 8 MPa b = width…

Q: Determine the reaction/s at each support, given the data and figure below. X = 6 kN/m Y = 14 kN/m L…

Q: If the given figure shows the geometry of a certain unsymmetrical weir, where angle A=48-degrees and…

Q: draw the shear and moment diagram of the figure.

Q: num wheel load that the pavement bearing capacity is equivalent to 0.- 45-deg cone pressure…

Q: 1. Given, for a compound curve: plus of PI = 14 + 29.31, A = 97°35'15"; the first radius R, = 400',…

Q: Draw a neat, labelled layout and ighlight the necessary support services required for functioning…

A: The layout of the cardiological department is drawn below it consist of following parts Reception…

Q: Two tangents intersect at v with back tangent having a grade of - 2.75q and forward tangent of…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Input values only without…

A: A section have been given and it has been asked to determine centroid of the same. Please refer step…

Q: A rectangular channel (n=0.011) 18 m wide to carry water at a flow rate of 35 m³/s. The slipe of the…

A: Given data in question Constant value Width Discharge Slope To find out Critical depth Specific…

Q: The company that you are working for is currently in the planning stage of road construction in an…

Q: The 200-kg crate rests on the ground for which the coefficients of static and kinetic friction are…

A: Determine speed of crate,V=?

Q: Q1: The following data were collected while running a closed traverse ABCDA. Calculate the missing…

Q: For the beam and loading shown, (a) write the equations of the shear and bending-moment curves, (b)…

Q: Which advantages fall under which type of pile? Please answer this asap. For upvote. Thank you very…

A: The foundation or substructure of the building is the structure lying below the ground surface to…

Q: repair the sidewalks only if he is notified that it is a problem provide assistance to anyone who…

Q: A 5.5 m diameter circular concrete culvert has a drainage water flowing at a height of 4.6 m.…

Q: A 3 m x 3 m square precast reinforced concrete segments to be installed by pushing them through

Q: +538 having an elevation of cerline having an elevation of le of the bridge located 55 cr

Q: egrate the equation below using Four-Point Gauss Quadrature betwe dy = 0 to y = 2.5. Hint: this is a…

Q: 4.32 Derive the area moment of inertia for a rectangular se tion with a cutout as shown in Sketch c.…

A: From below sketch we need to derive the area of the moment of inertia. This can be calculated by…

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

Determine the reaction/s at each support, given the data and figure
below.
X 3 kN/m
Y = 18 kN/m
L 1 m
What is the reaction (kN) at the roller support? Type answer in two (2)
decimal places only without the unit.
Y (kN/m)
Y- 5
X (kN/m)
(kN/m)
5 kN/m
5 kN/m
A
10 m
L (m)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the beam loaded as shown in the figure 1, determine the reaction at A in kN using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 4.7 m, b = 18 kN/m, c = 15 kN.
For the beam loaded as shown in the figure 2, determine the reaction at D in kN using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.
Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
A 4-ft-diameter log (sg. = 0.82) divides two shallow water as shown in the figure. Compute the vertical reaction at point C, if the log is 12 ft long. CHOICES A.) 658.68 B.) 568.88 C.) 856.86 D.) 865.65
For the beam loaded as shown in the figure 2, determine the moment reaction at A in kN-m using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.
An open rectangular tank 3.8m high, 2.5m wide and 6m long is filled with water at a depth of 2.2m. If it is accelerated at 2.3 m/s^2 and is moving at a plane inclined 15 degrees from the horizontal, determine the following: a. acceleration of the vessel along the horizontal; and b. angle of fluid inclination. Note: Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3.
A 4-ft-diameter log (sg. = 0.82) divides two shallow water as shown in the figure. Compute the horizontal reaction at point C.
For the system shown, the masses of A and B are 55 kg and 135 kg, respectively. The cocfficient of static friction between block B and the surface C is 0.12 and the coefficient of static friction between blocks A and B is 0.10. The coefficient of friction between the rope and the pulley is 0.10. What is the maximum mass M that can be suspended as shown and still maintain equilibrium?
A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in diameter. If 2 liters of water per minute flow upwards through the pipe the pressure difference across the pipe is 35 kpa. Calculate the flow downwards through the pipe if the pressure across the pipe is to be zero. The losses across the pipe are given by h1=k((v2) ²-(v1)²)/2g,where v1 and v2 are the velocities in the 50 mm and 25 mm sections respectively.
Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 1m x 5m gate shown in the figure. Pressure of air = 32 kPa Fluids: fluid a (s=3.93) fluid b (s=0.23) fluid c (s=1.19) h1= 0.7 m h2= 1.6 m h3= 3.7 m Round your answer to 3 decimal places.
The water flows from the pipe shown in the figure with a flow rate of 0.025 m3 / s and emerges into the atmosphere as a free jet. Flow is frictionless and gravity effects are negligible. Since the pressure in the section (1) is 150kpa, find the x and y components of the force required to hold the pipe in place. [rsu = 999 kg / m3]
A tank containing water moves horizontally (parallel to length) with a constant linear acceleration of 3 m/s2 . The tank is 3 m long and the depth of water when the tank is at rest is 1.5 m. FIND THE FOLLOWING: A. what angle (degrees) does the water make during acceleration? B. what is the minimum height of the vessel for no spilling of water? C. what is the maximum pressure head? (m)