Please show the complete solution. Write the given values and constant value (if there is). Write eligibly. Thank you. Determine the reactions at the pin support and the applied moment if the bar of Figure 3has a mass of 50 g. If e is 15º and the angular acceleration is 20 rad/sM– 3 m

Given: The mass of bar, m = 50 g The angle, θ = 15° The angular acceleration of bar, α’ = 20 rda/s^2

Answered: Determine the reactions at the pin…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

One of the ends of the rigid rod AB of mass m and length L = 4R is attached to the edge of the radius R disc by a pin. The other end of the rod can slide freely on the ground without friction. A motor connected to the center of the disk at point O rotates the disk at a constant angular velocity D. Find all the forces acting on the rod at the moment θ = 30 degrees and the direction OB is vertical at the moment shown in the figure.
The force F of 250 N is applied because a block with a mass of 20 kg and a radius of inertia of 160 mm as shown in the figure. This force lifts the weight B of 10 kg. Calculate the pulley angular acceleration and the normal acceleration of weight B, tension in the cable and reaction in the pulley bearing.
The force F 250 N is applied to a wheel weighing 20 kg and having a radius of inertia of 150 mm as shown in the figure. This force lifts a weight B of 10 kg. Calculate the angular acceleration of the pulley and the normal acceleration of the weight B, the tension of the rope and the reaction in the bearing of the pulley.
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.
The 20kg uniform rectangular plate is supported by an ideal pivot at O and a spring which must be compressed prior to being slipped into place at point A. If the modulus of the spring is k=2KN/m, what must be its undeformed length?
The homogeneous bars have a mass as follows: bar AC has a mass of 7 kg, bar ABhas a mass of 10 kg, and rod BD has a mass of 2 kg. In the drawn position, therod AC has an angular velocity of 4 rad/s and an angular acceleration of 2 rad/s2, both clockwise.Determine the magnitude of the moment M acting on the member AC. Give all the equations neededto solve this question without calculating it
QUESTION: It is wanted to withdraw from A end with V_A velocity velocity (a_A = 0 m / s ^ 2) as shown on AB rod. Find the force F that will satisfy this condition. In this case, what are the support reactions at A and B points? Ignore the mass and atalat moments (I) and friction forces of the wheels. The inertia moment table of the rod is given.
When a 6 kg load is hung at point O and member AO is adjusted until it is horizontal, the angle is measured to be 35 Determine the final readings of spring scales S_{1} and S_{a} and solve for the moments they produce about each of the axes passing through A and B if member AB is measured to be 38 cm.
The mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear Bits mass is 3kg and the turning radius is 80 mm. When the system is stationary to gear B. Moment of 6 N.m is applied. By neglecting friction;Find the tangential force from gear B to gear A.
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
The ideal spring of constant k=2.6kN/m is attached to the fitted at point A and the end fitted at point B, as shown. The spring is unstretched when theta(A) and theta(B) are both zero. If the fitted is rotated 15⁰ clockwise and the end fitting is rotated 30⁰ counterclockwise, determine the vector expression for the spring force F. Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass of 50 g. If e is 15° and the angular acceleration is 20 rad/s M - 3 m-