Determine the resistance of an aluminium coil of 183 cm as diameter consists of 14500 turns and the mean length per turn is 4883 cm. Take the electrical conductivity of the aluminium coil as 0.37 MS/m. Solution: Area of Cross-section of the Coil (in m?) Total Length (in m) The Resistance of the Coil (in n)

Determine the resistance of an aluminium coil of 183 cm as diameter consists of 14500 turns and the mean length per turn is 4883 cm. Take the electrical conductivity of the aluminium coil as 0.37 MS/m. Solution: Area of Cross-section of the Coil (in m?) Total Length (in m) The Resistance of the Coil (in n)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.54P

See similar textbooks

Similar questions

The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per square meter will be transferred in this system if the temperature difference is 10C?
A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
A steam pipe 200 mm in diameter passes through a large basement room. The temperature of the pipe wall is 500C, while that of the ambient air in the room is 20C. Determine the heat transfer rate by convection and radiation per unit length of steam pipe if the emissivity of the pipe surface is 0.8 and the natural convection heat transfer coefficient has been determined to be 10 W/m2K.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
The thermal conductivity of fibreglass insulation at 67F is 0.02 Btu/h ft F. What is its value in SI units?
A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
A 1.69 m wide by 1.06 m high metal plate must be insulated to prevent contact burn injuries. If the heat transfer rate is 131 W and the temperature across the insulation must be reduced from 87.9°C to 40.2°C, what is the minimum thickness (in cm) of insulation required [round your final answer to two decimal places]? {kins = 0.033 W/m∙K}
The inner and outer surface temperature of a 5.1 mm thick glass window are 17.6 and 7.1 oC, respectively. What is the heat loss in W through a window that is 1 m by 3 m on a side? The thermal conductivity of glass is 1.4 W/mK. Please keep one decimal and take positive value for the final answer.