A plane wall of thickness 50 cm having thermal conductivity 17.5 W/m°c. temperature at right and left surface are 10°C and 150°c. determine the heat flux through the wall? 875 W/m A В 1400 W/m2 2 2575 W/m C 2 D 4900 W/m*
Q: Heat is conducted through a material with a temperature gradient of – 9000 °C/m. The conductivity of…
A: Given in problemtemperture gradient with length dTdx=9000 °C/m.Thermal conductivity (k) =…
Q: Q: Consider the section of wall as shown in the figure, assuming one dimensional heat flow,…
A:
Q: A metallic solid cylinder has a diameter of 11 cm and initial temperature of 300°C. The cylinder is…
A: GIVEN:diameter =11 cminitial temperature =300°Cenvironment temperature =50°C heat transfer…
Q: Q2. The inner and outer surfaces of a 6-m x 6-m brick wall of thickness 30 cm and thermal…
A:
Q: A wall of 3 m height and 4 m width having an insulation layer is shown in the figure. The thickness…
A:
Q: Consider a person standing in a breezy field at 10°C. Determine the total rate of heat transfer from…
A: In heat transfer analysis, the rate of change of state is evaluated by calculating the rate of heat…
Q: The heat flow rate through a 3 cm thick for a temperature wood board difference of 30°C between the…
A:
Q: A wall is constructed of two layers of sheetrock spaced by 5 cm x 12 cm wood studs. The space…
A: The resistance of a plain wall can be obtained by the formula R=LkA, where R is the thermal…
Q: The furnace wall shown in the figure is made of a material with a thermal conductivity of 5 W / m °…
A: Given data: Thermal conductivity of wall = 5 W/m °C Emissivity = 0.95…
Q: An aluminum pan with a thermal conductivity of = 237 /m.K is used to heat water as shown in the…
A: As per given D=15cm K=237 w/m°c Q=1400w T=105°c We have to determine temperature of outer surface
Q: A steam pipe 50 mm diameter and 2.5 m long has been placed horizontally and exposed to still air at…
A:
Q: A hollow sphere is constructed of aluminium (k = 204 W/m K) with an inner diameter of 4 cm and an…
A: Given:Inner diameter,d=4cm=0.04mSo,inner radius=r=0.04m2=0.02mOuter diamter,D=8cm=0.08mSo,outer…
Q: Two industrial steel pipes are carrying 200 °C steam. The internal diameter of both pipes are 2.0 cm…
A:
Q: A long pipe carries hot water and loses heat by convection to the surrounding air at T =22 °C and…
A: In general, there are three modes by which heat gets transferred from one place to another. The…
Q: An aluminum fin is attached to a transistor that generates heat at the rate of 300 W. The fin has a…
A: Write the given values along with the suitable variables. Note: The value of heat generation is way…
Q: A circular profile fin 2.3 cm in diameter and 20 cm in length is constructed of aluminum (k=20 W/m…
A: give d=2.3mm L=20mm K=20 w/m°cT0=900c T∞=20°c h=12…
Q: A 10-cm diameter pipe is covered by 2 layers of lagging. The inside layer is 4 cm thick and has a…
A:
Q: A rectangular window in a home has a length of 1.5 m and a height of 0.80 m. If the window allows…
A:
Q: Q1 A. 1. When may one expect radiation heat transfer to be important? 2. Name some good conductors…
A: A. 1. Importance of Radiation heat transfer Note :- you have posted multiple questions on…
Q: Straight, rectangular cross-section fins made of metal with constant thermal conductivity k = 235…
A: (a) Fin efficiency, ηfin = 80.57%. (b) Heat transfer rate from fin, qfin = 444.83 W.
Q: The outer facing of a room is constructed from 25 cm thick brick, 2.5 cm of mortar, 10 cm of…
A: Givent4=25cmk4=0.52 W/mKt3=2.5cmk3=0.52 W/mKt2=10cmk2=0.186 W/mKt1=1.2cmk1=0.096 W/mKA=10m2
Q: A square plate heater (15 cm by 15 cm) is inserted between two slabs. Slab A is 2 cm thick (k-50…
A:
Q: If a cylinder with an infinite length of 2 cm in diameter and a heat conduction coefficient of 12.5…
A: Diameter of the cylinder, d=2 cm=0.02 m Conduction coefficient, k=12.5 W/m.K Convection coefficient,…
Q: Consider a 150-W incandescent lamp. The filament of the lamp is 5.7-cm long and has a diameter of…
A: GIVEN DIAMETER OF FILAMENT =D =1.2MM=0.0012 M LENGHT OF FILAMENT =L= 5.7 CM=0.057 M ASSUMPTION…
Q: Steam at 320°C flows in a stainless steel pipe (k = 15 W/m-°C) whose inner and outer diameters are 5…
A: Given Radius, r1 = 2.5 cm r2 = 2.75 cm r3 = 5.75 cm
Q: Two industrial steel pipes are carrying 200 °C steam. The internal diameter of both pipes are 2.0 cm…
A: First option is correct.
Q: The inner and outer surfaces of a 0.3 cm thick 1.8 m x 2.5 m window glass in winter are 20°C and…
A:
Q: Calculate the heat loss in a pipe 109.7 mm inside diameter and 13.7 m length covered with a layer of…
A:
Q: L 2L L A/4 2. Assumption: Surfaces normal to x are isothermal,contact resistance between layers is…
A: Equivalent Thermal Circuit
Q: A long pipe carries hot water and loses heat by convection to the surrounding air at To =22 °C and…
A: There are three modes of heat transfer:- 1) conduction heat transfer which is governed by fourier…
Q: 6. A wall of a basement is made of insulation with (k=0.035 W/m-°C), which is between two layers of…
A:
Q: Heat is produced in a long resistance wire q.u= 1.5 W/cm3. The radius of the wire is given as r1=0.3…
A:
Q: Determine the heat flow (in Watts) across a plane wall of 8.1m thickness with a constant thermal…
A: given; →thickness of wall (t)=8.1m→thermal conductivity…
Q: A 0.083-in-diameter electrical wire at 90°F is covered by 0.02-in-thick plastic insulation (k =…
A: Given data: Diameter of electric wire, d = 0.083 in. Thickness of plastic insulation, t = 0.02 in.…
Q: Two industrial steel pipes are carrying 200 °C steam. The internal diameter of both pipes are 2.0 cm…
A:
Q: A cylindrical insulation for a steam pipe has an inside radius of 5 cm, an outer radius of 10 cm,…
A: Given:Inside radius,r=5 cm=0.05mOuter radius,R=10 cm=0.10 mThermal conductivity,K=0.5WmKInside…
Q: A metallic solid cylinder has a diameter of 11 cm and initial temperature of 300°C. The cylinder is…
A: A metallic solid cylinder has a diameter of 11 cm and an initial temperature of 300o C. The cylinder…
Q: A thick-walled tube of stainless steel with thermal conductivity k=19 W/m°C has inner diameter of 10…
A:
Q: Two slabs sandwich a square plate heater of dimensions 30 cm by 30cm. One slab is 13 mm thick (k =…
A: Given data: t1=13 mmk1=0.67 W/m°Ct2=36 mmk2=0.47 W/m°CTO=60°CQ=2 kW Need to determine the maximum…
Q: A plane brick wall, 25 cm thick, is faced with 5 cm thick concrete layer. If the temperature of the…
A: It is very conceptual numerical of heat transfer subject. Used concept is Heat transfer through…
Q: A steel pipe 150mm external diameter conveys steam at a temperature of 260°c and it is covered by…
A:
Q: A polished metal pipe (8 cm) outside diameter and 350 K temperature at the outer surface is exposed…
A: Given data:
Q: 2. A steel plate of k=50W/mK and thickness 10cm passes a heat flux by conduction of 25kW/m2. If the…
A:
Q: A 30-m-long section of an 8-cm-diameter norizontal hot water pipe passes through a arge room whose…
A: As per the calculation, the nearest option is b.
Solve this one too
Step by step
Solved in 3 steps with 1 images
- 3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
- 2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.2.29 In a cylindrical fuel rod of a nuclear reactor, heat is generated internally according to the equation where = local rate of heat generation per unit volume at r = outside radius = rate of heat generation per unit volume at the centerline Calculate the temperature drop from the centerline to the surface for a 2.5-cm-diameter rod having a thermal conductivity of if the rate of heat removal from its surface is 1.6 .
- A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.A total of 10 rectangular aluminum fins (k =203 W/m·K) are placed on the outside flat surface of anelectronic device. Each fin is 100 mm wide, 20 mm highand 4 mm thick. The fins are located parallel to each otherat a center-to-center distance of 8 mm. The temperature atthe outside surface of the electronic device is 60°C. The airis at 20°C, and the heat transfer coefficient is 100 W/m2·K. Determine (a) the rate of heat loss from the electronic device to the surrounding air and (b) the fin effectiveness.
- Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. Thewater flow over the surface of the apple creates a convective heat-transfer coefficientof 15 W/(m2-K). Assume the apple can be described as a sphere with a 10 cm diameterand the geometric center is to be reduced to 10°C. The apple properties include thermalconductivity of 0.45 W/(m-K), specific heat of 3.950 kJ/(kg-K), and density of 940 kg/m3.a. Determine the time that the apples must be exposed to the water.b. If the apple is submerged only for 2 hours, what will be its center temperature?3. A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. The density of the product is 1000 kg / m³, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -2 ° C. After 11 hours in the freezing medium -30 ° C, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder. h = Answer W / (m² K).A 2 cm thick steel pipe (thermal conductivity 43 W/[m °C]) with 6 cm inside diameter is being used to convey steam from a boiler to process equipment for a distance of 40 m. The inside pipe surface temperature is 115°C, and the outside pipe surface temperature is 90°C. If there is 600kW of heat loss, what is the thickness of the pipe?