Q2. The inner and outer surfaces of a 6-m x 6-m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m-°C are maintained at temperatures of 20°C and 5°C, respectively (Figure 2). Determine the rate of heat transfer through the wall, in W. Brick wall 20°C S°C 30 cm Figure 2

Q2. The inner and outer surfaces of a 6-m x 6-m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m-°C are maintained at temperatures of 20°C and 5°C, respectively (Figure 2). Determine the rate of heat transfer through the wall, in W. Brick wall 20°C S°C 30 cm Figure 2

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.19P: 1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the...

See similar textbooks

Related questions

Q: 42 oC with convection heat transfer coefficient of 9.0 W/m2 K. Solar radiation incident on the…

A: given:T0=45CT∞=42C h=9w/m2kthickness l=25cm

Q: The inner surface of a 2 inch wall is 70C and its outside surface temperature is 34C. Determine the…

A: To find: The steady state heat transfer. Given: The thickness of the wall is t=2 in. The inner wall…

Q: Under steady-state conditions, the wall of a brick house is measured to have an inside temperature…

Q: The inner and outer surfaces of a 25-cm-thick wall are at 27 oC and 45 oC, respectively. The outer…

Q: A 50 KW electric furnace measure 1.2m x 1.0m x 0.8m. When the temperature inside the furnace is…

A: given; electric power (P)=50kwfurnace dimension=1.2m*1m*0.8mtemperature inside the furnace…

Q: 56. The inner surface of a 2 inch wall is 70C and its outside surface temperature is 34C. Determine…

A: To find : The steady state heat transfer rate. Given data : The thickness of wall is b=2 inch1 ft12…

Q: 3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ =…

Q: An infinitely long pin fin, attached to an isothermal hot surface, transfers heat at a steady rate…

Q: Consider a large plane wall of thickness L=0.35 m. The wall surface at x=L is insulated, while the…

Q: If the rate of heat flow through a furnace wall is 0.94 kW/m². The wall consisting of 0.20 m thick…

Q: insulator has a thermal conductivity of 20 W/m ºC s used to separate two heat sinks whose…

Q: A 25 cm thick brick wall of 4 m by 3 m has inner and outer surfaces at 15°C and 7°C, respectively.…

Q: 0.60W / m•º C _7. A brick wall is 5.0 m long, 3.0 m high, and 30 cm thick. The conductivity of brick…

Q: If the rate of heat flow through a furnace wall is 0.94 kW/m². The wall consisting of 0.20 m thick…

A: Heat flux will be same across the layers. 1. The temperature of the gases inside the furnace is…

Q: A plane wall 15 – cm thick has a thermal conductivity given by the relation k = 2.0 + 0.0005 T, W/m…

A: Given data t=15 cm, K=2+0.0005 T ω/m.K T1=150°C T2=50°C Need to determine the rate of…

Q: A rectangular steel plate having a area of 750 cm2 is heated from 20 °C to 220 °C. What is its…

Q: An irregularly shaped solid made of a material with a density of 3200 kg/m³ has a volume of 0.003 m3…

A: Given:ρ=3200 Kg/m3V=0.003 m3As=0.07 m2k=300 W/m.KC=500 J/Kg.KTb-T∞=100°CT-T∞=13*100°Ch=60 W/mK

Q: The brick wall of a house measures 4 x 7 m and has a thickness of 0.3 m. The thermal conductivity of…

A: given data as per question Dimensions of the brick wall = 4m×7m Thickness of the wall = 0.3 m…

Q: Consider a large plane wall of thickness L=0.30 m. The wall surface at x=L is insulated, while the…

A: Heat transfer Heat transfer is a process in which heat is transfer from high temperature to low…

Q: A circuit board houses on its surface 120 closely spaced logic chips, each dissipating 0.12 W. If…

Q: A rectangular wall of length "L" m and height "H" m is made from a thick bricklayer. The rectangular…

Q: 9. A plane wall 6.2 cm thick generates heat internally. The wall is made of a material with thermal…

Q: Q: A large plane wall of thickness (L= 0.3 m), thermal conductivity ( k = 40 W/m-°C), and surface…

A: Given, L = 0.3 mk = 40 W/m °CA = 0.4 m2T(0) = 70 °Cq' = 1200kk + 20L=1200 (40)40 + 20 (0.3)=1043.48…

Q: Consider a wall consisting of two layers, A and B, with the following properties: = 1.5 W/m.K; LA =…

Q: Question 2: A circuit board houses on its surface 120 closely spaced logic chips, each dissipating…

Q: Q1: A spherical container of inner radius ri=40 cm, outer radius r2-41 cm (k=1.2 W/m°C) is used to…

A: Assumption:- 1) Heat Transfer takes place in One dimension 2) Material is isotropic

Q: A window is replaced by a wall with thick insulation. The thermal conductivity of the same area will…

A: As per policy, one question can be answered. Hence, first question is answered. Given, Thermal…

Q: Consider a large plane wall of thickness L=0.35 m. The wall surface at x=L is insulated, while the…

Q: Consider a wall consisting of two layers, A and B, with the following properties: kA = 1.5 W/m.K; LA…

Q: A plane wall of thickness 50 cm having thermal conductivity 17.5 W/m°c. temperature at right and…

A: Data given- Thickness ∆x = 50 cm K = 17.5 W/m°C T1 = 150°C T2 = 10°C

Q: n irregularly shaped solid made of a material with a density of 3200 kg/m³ has a volume of 0.003 m3…

A: Given:ρ=3200 Kg/m3V=0.003 m3As=0.07 m2k=300 W/m.KC=500 J/Kg.KTb-T∞=100°CT-T∞=13*100°Ch=60 W/m.K

Q: Carnot refrigerator operates between reservoirs at -20∘C∘C and 40 ∘C∘C in a 25∘C∘C room. The…

Q: A 2x2-m glass window, 1 cm thick is subjected to 10°C and 3°C inner and outer temperatures…

A: As per given question A 2x2-m glass window, 1 cm thick is subjected to 10°C and 3°C inner and outer…

Q: 1- A solid infinitely long cylinder, radius 2 cm, has uniform internal heat generation. The…

Q: The inner and outer surfaces of a 5m x 10m brick wall of thickness 30 cm and thermal conductivity…

A: As per given question Determine the rate of heat transfer through the wall, in W. [Note: State all…

Q: (A) Choose the right answer 1.The temperature profile for heat conduction through a wall of constant…

Q: Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂…

A: Given:T1=120°CT2=50°CL=0.2 mk=1.2 W/m.KA=15 m2

Q: A long rod with a diameter of 2 cm is welded to the outer wall of the boiler and extends out. The…

Q: Q2/ A plane wall generates heat internally at the rate of 0.2 MW/m' with 8.0 cm thick. One side of…

Q: Consider a large plane wall of thickness L=0.30 m. The wall surface at x=L is insulated, while the…

A: Given data, L = Thickness of the wall = 0.3 m T1 = Temperature of the wall where x= 0 m, is 32 °C k…

Q: Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂…

Q: The temperatures on the left and right surfaces of a 15-cm thick wall are 375°C and 85°C. The wall…

A: Given data, k= 0.78 W/m°C Density is 2700 kg/m3 Cp= 0.84 kJ/kgK Need to find the heat flux q =…

Q: A spherical container ( k= 30 W/moC ) with inner radius r1 = 2 m and outer radius ro=2.1 m is is…

A: Write the expression for the heat equation and the boundary conditions.

Q: How much heat is conducted in 24.0 hours through a 21.0 cm thick concrete wall whose thermal…

A: given that , thickness of wall =21 cm =0.21m thermal conductivity of…

Q: A wall of length "L" m and height "H" m is made from a thick bricklayer of 26 cm with thermal…

Q: A plane wall 3.5 cm thick generates heat internally. The wall is made of a material with thermal…

Q: Q5/ A solar concentrator provides a heat flux of 8000 W/m? to heat a 10 mm plate on one side. The…

A: Answer: Heat flux , q= 800 w/m2 Length of plate, L= 10mm = 0.010 m convertion Heat transfer…

Q: A circuit board houses on its surface 120 closely spaced logic chips, each dissipating 0.12 W. If…

A: Given data: The number of the chip, n = 120. The power dissipated by each chip, P = 0.12 W. The…

Q: 2. A steel plate of k=50W/mK and thickness 10cm passes a heat flux by conduction of 25kW/m2. If the…

Question

Q2. The inner and outer surfaces of a 6-m x 6-m brick wall of thickness 30 cm and thermal
conductivity 0.69 W/m-°C are maintained at temperatures of 20°C and 5°C, respectively (Figure
2). Determine the rate of heat transfer through the wall, in W.
Brick
wall
20°C
S°C
30 cm
Figure 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is
A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall is insulated, and the other side is exposed to an environment at 90C. The convection heat transfer coefficient between the wall and the environment is 500 W/m2 K. If the thermal conductivity of the wall is 12 W/m K, calculate the maximum temperature in the wall.
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
2.44 To determine the thermal conductivity of a long, solid 2.5-cm-diameter rod, one half of the rod was inserted into a furnace while the other half was projecting into air at . After steady state had been reached, the temperatures at two points 7.6 cm apart were measured and found to be and , respectively. The heat transfer coefficient over the surface of the rod exposed to the air was estimated to be 22.7 . What is thermal conductivity of the rod?
A plane wall 15 – cm thick has a thermal conductivity given by the relation k = 2.0 + 0.0005 T, W/m – K where T is in Kelvin. If one surface of this wall is maintained at 150 oC and the other at50 oC, determine the rate of heat transfer per square meter. Sketch the temperaturedistribution through the wall.
q1 The inner and outer surfaces of a 5-m x 6-m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m · °C aremaintained at temperatures of 20°C and 5°C, respectively. Determine the rate of heat transfer through the wall, in W.