Answered: Determine the shear and moment as a…

Determine the shear and moment as a function of x (location of the beam section), and then draw the shear and moment diagrams of the beam given in Figure 1. 8 kN 6 kN 4 kN F 1m 1m 1 m BEL.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 ft, b=9.0 ft, c=4.0 ft, d=3.5 ft, w = 5.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Ay =___________ kips, Ey = __________ kips. Determine the shear force acting at each of the following locations:(a) x = 0+ ft (i.e., just to the right of support A)(b) x = 3.5 ft(c) x = 12.5 ft(d) x = 16.5– ft (i.e., just to the left of D)(e) x = 16.5+ ft (i.e., just to the right of D)(f) x = 20.0– ft (i.e., just to the left of support E) Answer: a to f ) V = ________ kips Use the graphical…
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=6.5 ft, b=24.0 ft, P = 32 kips and w = 9.5 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. 1. Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) 2.Determine the shear force acting at each of the following locations: (in kips)(a) x = 6.5- ft (i.e., just to the left of point B)(b) x = 6.5+ ft (i.e., just to the right of point B)(c) x = 28.5 ft 3.Determine the bending moment acting at each of the following locations: (in kips-ft)(a) x = 6.5 ft (i.e., at point B)(b) x = 28.5 ft 4.Use your…
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=5.8 ft, w=215 lb/ft, MD=6700 lb⋅ft, and P=1200 lb. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m? Use the integration method
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
The piston of a reciprocating engine exerts a firce of 180 kN on crosshead when the crank is 35 degree (angle beta) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.65 m, find, in kN. a) the guide force FG and , b) the firce on the connecting rod Rc .hint: radius AC is 1/2 of the stroke and Angle "phi" may be solved using sine law. Draw FBD
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=12.0 ft, b=6.5 ft, c= 7.0 ft, w = 7 kips/ft and M = 230 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the shear force acting at each of the following locations:(a) x = 0+ ft (i.e., just to the right of support A)(b) x = 12.0 ft (i,e., at point B)(c) x = 18.5- ft (i.e., just to the left of the support C)(d) x = 18.5+ ft (i.e., just to the right of the support (C)(e) x = 24.5 ftNote that x = 0 at support A. Determine the bending…
Develop an expression for the shear force V(x) as a function of position (x) along the beam.
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=8.5 ft, b=24.0 ft, P = 30 kips and w = 5.5 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the shear force acting at each of the following locations:(a) x = 8.5- ft (i.e., just to the left of point B)(b) x = 8.5+ ft (i.e., just to the right of point B)(c) x = 30.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. Determine the bending moment acting at each of…
PLEASE ?? ANSWER ?Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A) Let a= 3.00 m, b= S.00 m. PB= 35kN, and PC = 65kN. Construct the shear force and bending-moment diagrams on paper and use t he results to answer the quest ions in the subsequent parts of this GO exercise. Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Please Answer: Ay = kN Dy = kN ?Part 2 Determine the shear force acting at each of the following locations: (a)x = 2 m (b)x =4m (c). x = 8 m Note that x = 0 at support A When entering your answers. use the shear-force sign convention detailed in Section 7.2. Please Answer: (a) V= kN (b) V=…