Determine the stress in each section of the bar shown below, which is subjected to an axial tensile load of (20KN). The central section is 30 mm Square Cross -Section; the other portions are of circular section, their diameters being indicated. what will be the total extension of the bar? For the bar material (E = 210 GN/m²). 250 100 400 mm * 1 20KN 0 20 KN 20 * 2 130mm 115

Determine the stress in each section of the bar shown below, which is subjected to an axial tensile load of (20KN). The central section is 30 mm Square Cross -Section; the other portions are of circular section, their diameters being indicated. what will be the total extension of the bar? For the bar material (E = 210 GN/m²). 250 100 400 mm * 1 20KN 0 20 KN 20 * 2 130mm 115

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
Before loading the plate, mark a line with the inclination shown. After the load is applied, the slope of the line decreases by 5x10^-3 rad. Determine the normal stress ?. Consider E = 2.1x106 kgf/cm^2 and v = 0.30. Express your answer in units of kgf/cm^2.
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
The block is subjected to a centrally-applied force of P=4.3 kipP=4.3 kip. Part A Determine the average normal stress on the material. Express your answer to three significant figures and include appropriate units.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. Select one: a. NH = 6.427 b. NH = 3.570 c. NH = 5.355 d. NH = 4.590
For the stress element shown below, which 2 points (σ, τ) in the stress domain could be used to define the diameter of the Mohr's Circle? (50 MPa, 25 MPa) (- 80 MPa, - 25 MPa) (- 80 MPa, 25 MPa) (50 MPa, - 25 MPa)
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is
The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a length of 127 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 423 mm2 Ealuminum = 70 GPa.
The masonry pier is subjected to the FFF = 810 kNkN load. Consider xx = 0.25 mm and yy = 0.5 mm. Neglect the weight of the pier. Determine the normal stress at corner A. Determine the normal stress at corner B. Determine the normal stress at corner C.
The compound bar is composed of brass and copper. It supports the axial loads shown below. Determine the stresses developed on both materials. Indicate whether the stress is tensile or compressive Answer: σbr = ___________________σco = ___________________