Determine the time required to acceierate a counter shaft of rotating mass 500 kg and radius of gyration of 200 mm to the full speed of 250 rpm from rest through a single plate clutch of internal and external radii 125 mm and 200 mm, taking coefficient of friction as 0.3 and axial spring force of 600 N Assume that only one side of clutch is effective.

Determine the time required to acceierate a counter shaft of rotating mass 500 kg and radius of gyration of 200 mm to the full speed of 250 rpm from rest through a single plate clutch of internal and external radii 125 mm and 200 mm, taking coefficient of friction as 0.3 and axial spring force of 600 N Assume that only one side of clutch is effective.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A min cage of mass 4t is to be raised with an acceleration of 1.5m/s2 by a cable passing over a hoist drum of 1.5m diameter. What is the power required when the load has reached a velocity of 6m/s, neglecting the inertia of the drum and weight of the cable, but allowing for bearing friction torque of 3kN at the drum? What is the power required at a uniform velocity of 6m/s
A drum A, of mass 200 kg, external diameter 380 mm and radius of gyration 150 mm, rotates on frictionless bearings at 250 rev/min. A stationary drum, B, of mass 50 kg, external diameter 200 mm and radius of gyration 80 mm, mounted on a frictionless axis parallel to that of A, is pressed into contact with A with a force of 90 N. The coefficient of friction is 0·25. Determine: The final speeds of A and B. (b) The time of slipping. (c) The time of slipping if a torque is applied to A, to maintain the speed of A as a constant 250 rev/min.
A spool of mass 60 kg is supported on two rollers at A and B as shown in FigureQ1(c). Neglect the mass of the inelastic cable, friction and the mass of therollers at A and B. Knowing that a constant pulling force P is applied in order tounwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spoolis (604) mm, Appendix Ashows the examples of identifying the radius of gyration using student ID.(i) Determine the angular acceleration of the spool. (ii) Determine the pulling force P. (iii) Explain with calculation on ways to increase the acceleration of cablebeing pulled. [
In your job as a mechanical engineer you are designing aflywheel and clutch-plate system. DiskA is made of a lighter material than disk B, and the moment of inertia ofdisk A about the shaft is one-third that of disk B. The moment ofinertia of the shaft is negligible. With the clutch disconnected, A isbrought up to an angular speed v0; B is initially at rest. The acceleratingtorque is then removed from A, and A is coupled to B. (Ignorebearing friction.) The design specifications allow for a maximum of2400 J of thermal energy to be developed when the connection ismade. What can be the maximum value of the original kinetic energyof disk A so as not to exceedthe maximum allowed value of the thermalenergy?
Q12 / A Porter governor has links 150 mm long and are attached to pivots at a radial distance of 30 mm from the vertical axis of the governor. The mass of each ball is 1.75 kg and the mass of the sleeve is 25 kg. The governor sleeve ready to rise at 300 rpm when the links are at 30 ° to the vertical. Assuming the friction force to be constant, find the value of the friction force, minimum and maximum speed of rotation when the inclination of the links is 45 ° to the vertical.
A 2000-lb bike with a rear wheel drive has awheelbase of 10 ft. The c.g. is 3 ft above thepavement and 4 ft ahead of the rear wheels.The coefficient of friction is 0.60 between thetires and the pavement. Determine the inertia force on themotorcycle when the acceleration ismaximum.a. 2846.57 lbs b. 2675.66 lbsc. 2864.75 lbs d. 2666.75 lbs
On a level test track, a car with anti locks brakes and 90% braking efficiency is determined to have a theoretical stopping distance (ignoring aerodynamic resistance) of 408-ft (after the brakes are applied) from 100-mi/h. The car is rear-wheel drive with a 110-inch wheel base, weighs 3200-lb, and has a 50/50 weight distribution (front to back), a center of gravity that is 22-inches above the road surface, an engine that generates 300-ft lb of torque, an overall gear reduction of 8.5 to 1 (in first gear), a wheel radius of 15-inches and a driveline efficiency of 95%. What is the maximum acceleration from rest of this car on this test track? Thank you for helping.
ower shaft running at a steady speed of 175 rev/min driy 8 single-plate friction clutch of external and intern mm respectively. The masses on the countershaft have £ 250 mm and a total mass of 350 kg. The axial spring I 198 450 N, and 4 = 0-3. Assuming uniform acceleration guired to reach full speed from rest, and the work dissipad during that time. (U. Lond.) (Ans. : 99 g
Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, and μs=0.297. What is the maximum angular velocity allowable if the collar is to remain at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
A Mine cage of mass 4t is to be raised with an acceleration of 1.5 m/s by a rope passing over a hoist drum of 1.5 m diameter. What is the power required when the load has reached a velocity of 6 m/s, neglecting the inertia of of the drum and the weight of the rope, but allowing for a bearing friction torque of 3kN m at the drum. What is the power required at a uniform velocity of 6 m/s
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (254) mm while the bottom arms are (304) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position
The 2.00-kg slender rod shown is hanging in a vertical position and is pin-supported at point A. The slender rod is initially at rest until a 1.000-kg block C, strikes it at its end at point B.The block slides on a frictionless surface with a velocity of 3.50 m/s to the right. After the impact, it slides with a velocity of 1.250 m/s to the right, and the bar rotates with an angular velocity, ω'. 1. What gives the correct kinematic relationship relating the final velocity of the center of the rod, v' , and its angular velocity, ω'? 2. What is the coefficient of restitution, e, between the block and the slender rod? 3. What is the magnitude of the horizontal impulse at the support at point A?