Determine the value of entropy of steam at the entry to the steam turbine (accurate to 4 decimal places, u equations) assuming that the cp of superheated steam is 2.9503KJ/kg.K. HINT: Please donot use superheated steam table for enthalpy and entropy of superheated steam. instead sations since Cn is given.

Determine the value of entropy of steam at the entry to the steam turbine (accurate to 4 decimal places, u equations) assuming that the cp of superheated steam is 2.9503KJ/kg.K. HINT: Please donot use superheated steam table for enthalpy and entropy of superheated steam. instead sations since Cn is given.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Assuming an isentropic efficiency of 85 percent for both the turbine and the pump, determine the quality ofthe steam at the turbine exit, the thermal efficiency of the cycle, specific enthalpy (kJ/kg) at the condenser, and actual Qin (kJ/kg).
In an air standard gas turbine cycle, air at 14.5 psia and 70 F is first compressed to 80 psia in a compressor of 82 percent efficiency. The hot air leaving the combustion chamber at 1250 F is expanded back to 14.5 psia in a turbine of 85 percent efficiency. If a regenerator is inserted into the cycle to heat the air leaving the compressor to 650 F, determine the thermal efficiency of the cycle and the effectiveness of the regenerator.
Water enters the boiler of a steady-flow Carnot engine as a saturated liquid at 400 psia and leaves with a quality of 0.95. Steam leaves the turbine at a pressure of 20 psia. Show the cycle on a T-s diagram relative to the saturation lines, and determine (a) the thermal efficiency, (b) the quality at the end of the isothermal heat-rejection process, and (c) the net work output.
A simple Rankine cycle has a pump with an isentropic efficiency of 70%. The inlet and outlet pressures of the turbine are 6 MPa and 0.075 MPa, respectively, and steam enters the turbine at 550°C. Determine a) the isentropic efficiency of the turbine if the quality at the turbine outlet is to be ? = 1, b) the thermal efficiency of the cycle, c) the rate of heat input into the boiler if the net power output of the cycle is 10 MW.
Air enters the compressor of a gas turbine at 100 kPa and 25°C. Determine the back work rate and thermal efficiency of the Brayton cycle for a pressure ratio of 5 and a maximum temperature of 850°C.
The 7FA gas turbine manufactured by General Electric is reported to have an efficiency of 35.9 percent in the simple-cycle mode and to produce 159 MW of net power. The pressure ratio is 14.7 and the turbine inlet temperature is 1288°C. The mass flow rate through the turbine is 1,536,000 kg/h. Taking the ambient conditions to be 20°C and 100 kPa, determine: (a) the isentropic efficiency of the turbine and the compressor, (b) the thermal efficiency of this gas turbine if a regenerator with an effectiveness of 80 percent is added. Answers: (a) 0.849, 0.924 (b) 0.496
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Assuming an isentropic efficiency of 85 percent for both the turbine and the pump, determine the actual mass flow rate (kg/s) of the steam. (Use 2 decimal places for the final answer.)
A gas turbine cycle with a stage of reheat and regeneration operates under the conditions given below, as illustrated in the figure. The turbine efficiencies are 86%, and the compressor efficiency is 81%. Furthermore, the work output of the high-pressure turbine is just enough to drive the compressor. Determine the pressure at which the reheater operates. T1 = 1300 K, T6 = 3000 K, P1 = 450 kPa, P6 = 100 kPa
Air enters the compressor of a regenerative gasturbine engine at 310 K and 100 kPa, where it is compressed to 900 kPa and 650 K. The regenerator has an effectiveness of 80 percent, and the air enters the turbine at 1400 K. For a turbine efficiency of 90 percent, determine the thermal efficiency. Assume variable specific heats for air.
Please answer this problem. A turbine with one extraction for regenerative feedwater heating receives steam with an enthalpy of 3373 kJ/kg and discharges it with an exhaust enthalpy of 2326 kJ/kg. The ideal regenerative feedwater heater receives 11,338 kg/hr of extracted steam at 345 Kpaa (whose h=2745 kJ/kg). The feedwater (condensate from the condenser) enters the heater with an enthalpy of 140 kJ/kg and departs saturated at 345 Kpaa (hf=582 kJ/kg) .Calculate the turbine power in KW.( Ans. 18,081 KW)
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Assuming an isentropic efficiency of 85 percent for both the turbine and the pump, determine the specific enthalpy (kJ/kg) at the boiler outlet. (Use 2 decimal places for the final answer.)
A gas-turbine power plant operates on a simple Brayton cycle with air as the working fluid. The air enters the turbine at 120 psia and 2000 R and leaves at 15 psia and 1200 R. Heat is rejected to the surroundings at a rate of 6400 Btu/s, and air flows through the cycle at a rate of 40 lbm/s. Assuming the turbine to be isentropic and the compressor to have an isentropic efficiency of 80 percent, determine the net power output of the plant. Account for the variation of specific heats with temperature.