Determine the young modulus and the poisson's ratio of this steel. A 38 mm diameter, 50 mm in length steel bar is subject to a tensionalload of 260 kN. Under this loading, the rod elongates by 0.055 mmwhile the diameter shrinks by 0.0105 mm. If the proportional limit (S,)of the material is known to be 234 MPa, determine

Answered: Image /qna-images/answer/11ea792a-8c4a-49e9-a33f-8ad5d779ffc5.jpg

Answered: Determine the young modulus and the…

Engineering

Mechanical Engineering

Determine the young modulus and the poisson's ratio of this steel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as floows; 48 kips tension in the x directio, 60 kips compression in the y direction, and 54 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A steel cylinder (Est = 200 GPa and G = 79 GPa) undergoes an azial compression in which its diameter increases from 10 mm to 10.045 mm. If its final length is 123.00 mm, what was its original length?
A solid circular bar of steel (G = 78 GPa)transmits a torque T = 360 N ? m. The allowablestresses in tension, compression, and shear are90 MPa, 70 MPa, and 40 MPa, respectively. Also,the allowable tensile strain is 220 x10 -6 .(a) Determine the minimum required diameter d ofthe bar.(b) If the bar diameter d = 40 mm, what is Tmax?
Find the maximum value of P that will not exceed a stress in steel of 113 MPa, in aluminum of 91 000 KPa, or in bronze of 110 MPa if the aluminum rod is rigidly attached between a steel rod and a bronze rod.
A rectangular steel block is 4 inches long in the x-direction, 6 inches long in the y-direction, and 3 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniform distributed forces as follows: 55 kips compression in the x direction, 62 kips tension in the y direction, and 24 kips tension in the z direction. If the Poisson’s ration is 0.26 and E = 29 x 106 psi, determine the single uniform distributed load in the y direction that would produce the same deformation in the x direction as the original loading.
Determine the allowable value of force P (in Newton ), if a bar of diameter d = 32 mm and length L = 0.60m is loaded in tension by force P. The bar has modulus E = 44 GPa and allowable normal stress of 218 MPa . The elongation of the bar must not exceed 1.8 mm .
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (Es5 200 GPa, αs5 11.7 310–6/°C) and portion BC is made of brass (Eb 5 105 GPa, αb5 20.9 3 10–6/°C). Knowing that the rod is initially unstressed, determine the compressive force induced in ABC when there is a temperature rise of 50°C.
A given conical bar is tapering uniformly from 4 cm diameter to 15 cm and has a length of 40 cm. An axial force of 80 KN is applied at each end if the bar, Find the elongation of the bar. Note: Take E=200 GPa
A standard tension test is used to determine the properties of an experi-mental plastic. The test specimen is a 58-in.-diameter rod and it is subjected to an 800-lb tensile force. Knowing that an elongation of 0.45 in. and a decrease in diameter of 0.025 in. are observed in a 5-in. gage length, determine the modulus of elasticity, the modulus of rigidity, and Poisson’s ratio for the material
determine the allowable value of force P (in newton). if a bar of a diameter d=31mm and length L= 0.53m is loaded in tension by force P. The bar has modulus E= 42GPa and allowable normal stress of 161 MPa. The elongation of the bar must not exceed 2.1mm.