Develop the expression to determine: the elevation of the oil-water surface (Yi) and the pressure gradient for a water phase and an oil phase that is moving between two parallel plates showed on the figure. The flow rates at the inlet are 0.1 ft3/sec (same for both fluids) and the viscosities are 100 and 0.89 cps for oil and water respectively.

Develop the expression to determine: the elevation of the oil-water surface (Yi) and the pressure gradient for a water phase and an oil phase that is moving between two parallel plates showed on the figure. The flow rates at the inlet are 0.1 ft3/sec (same for both fluids) and the viscosities are 100 and 0.89 cps for oil and water respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Theflowrateofwaterthroughacastironpipeis5000GPM.The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe
Water at 57°C is flowing in a 4-in schedule 80 steel pipe when the flow rate is 0.0174 m³/s, the estimated pressure drop reacting across the manometer is 9. 3x10⁴Pa what size orifice should be used if the orifice coefficient is assumed to be 0.65?
Please answer all. I will rate. Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140 KPa greater than at A. f= 0.019 Determine the head loss in meters. choices: 7.25, 5.27, 2.75, 7.52 Determine the flow rate in lit/sec. choices: 522.88, 822.55, 885.22, 228.55
Refer to Fig 2 Find the flow rate in m3/sec/m length (at right angles to the cross section shown) through thepermeablesoillayer.Given:H=5m,H1 =2.8m,h=3.1m,L=60m,α=50,k=0.05cm/sec.
*hydraulics *Use handwritten Water Flows uniformly at a steady rate of 0.40 m3/s in a very long triangular flume which has side slopes of 1:1. the bottom of the flume is on a slope of 0.006 and n=0.012. Determine the critical depth of flow Choices: A.) 0.504 m B.) 0.604 m C.) 0.704 m D.) 0.804 m
Read the question carefully and give me right solution according to the question. Velocity =0.46 m/sec
Given the following conditions: air permeability (k) = 10−7 cm2, radius of extraction well (Rw) = 5.1 cm, radius of vacuum influence (RI) = 12 m, vacuum pressure (Pw)=0.90atm (i.e., 9.09×105g/cm-s2), and air viscosity = 1.8 × 10−4 g/cm-s. (a) Find the airflow rate per unit thickness of well screen Q/H by using graphical solution and applying equation solution to verify. (b) If the well is screened to the entire contaminated zone of 5 m, what is the airflow rate in cfm? Does this flow fall in the ideal range of 100–1000 cfm?
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa
Q.5 Determine the volumetric flow of water in m3/hr flowing in a pipehaving a diameter of 40 mm through an orifice having a diameter of 20 mm.Manometer reading across the tapping is 15 cm of Hg. Assume correctionfactor = 1. Reynolds number Ra is 105 . Assume density of water = 1000 kg/m3and kinematic viscosity is 10–2 stokes (cm2/sec). Also calculate the pressuredifference at the tappings. Assume Cd = 0.61.
water from a reservoir flows at 0.85 m3/s through a rigid pipe 1200 mm diameter and completely stopped by a closure of a valve almost instantly. Bulk modulus of water is 2.20 x 109 N/m2. a) Find the water hammer pressure for sudden closure. b) Find the discharge if water hammer pressure is 700 KPa. c) If the time of closure of valve is 4 sec. and located at 650 mm from the reservoir, find the water hammer pressure at flow rate at 0.85 m3/s.
Hydraulic structure Q.2: Given the following data of a head regulator: The discharge= 60 cumecs, bed level of the canal-52.2m, crest level of the regulator=52.8m, upstream water level-54.2m, downstream water level=53.9m. The dimension of gates= (2.5x3)m and the thickness of the piers is 0.9m. Neglect the velocity head and use coefficients of discharge= 0.8 and 0.577. Determine the water way of the regulator
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .c) Is the fluid pressure at the bottom of the venturi section greater than, less than, or equal to the fluidpressure at the narrowest region?