DHLIPS pts cuments/Week12 Compatibility 21-22-1%20(1).pdf 30 /31 - 100 + PROBLEM 2.35 The 1.35 m concrete post is reinforced with six steel bars, each with a 28 mm diameter. 450 mm Knowing that E, = 200 GPa and E,= 29 GPa, determine the normal stresses in the steel and in the concrete when 1.35 m a 1560 kN axial centric force P is applied to the post. [Ans. o, = -59.5 MPa; o = -8.63 MPa] Fig. P2.35 Seašon's Greetinas.

DHLIPS pts cuments/Week12 Compatibility 21-22-1%20(1).pdf 30 /31 - 100 + PROBLEM 2.35 The 1.35 m concrete post is reinforced with six steel bars, each with a 28 mm diameter. 450 mm Knowing that E, = 200 GPa and E,= 29 GPa, determine the normal stresses in the steel and in the concrete when 1.35 m a 1560 kN axial centric force P is applied to the post. [Ans. o, = -59.5 MPa; o = -8.63 MPa] Fig. P2.35 Seašon's Greetinas.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar. b) The deflection at D for the load determined in part (a).
b.The strong room of a school where an exam question papers are kept is made up ofrectangular metal bars.One bar has a width of 10 mmand would beable to withstand a maximum compressive stress of 20 MPa. i.Prove that,the minimum breadth of thisbar can withstand a burdened with a force of 3 KN. ii.If the bar in question is 2 mlong and decreases in length by 0.25 mmwhen aforce isapplied, then show thata percentage strain can be obtained. iii.What would be its Modulus of Elasticity, E?
The assembly shown consists of an aluminum shell (Ea= 10.6 * 106psi, αa=12.9 *10–6/°F) fully bonded to a steel core (Es= 29 * 106psi, αs= 6.5 *10–6/°F) and is unstressed. Determine (a) the largest allowable change in temperature if the stress in the aluminum shell is not to exceed 6 ksi, (b) the corresponding change in length of the assembly.
The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α= 10.5 × 10−6/°F] rod (1) and a solid 1.49-in.-diameter bronze [E = 15300 ksi, v = 0.15, α= 7.6 × 10–6/°F] rod (2). Assume L1=11 in., L2=22 in. If the supports at A and C are rigid and the assembly is stress free at 16°F, determine:(a) the normal stresses σ1, σ2 in both rods at 213°F (positive if tensile, negative if compressive).(b) the displacement uB of flange B (positive if to the right, negative to the left).(c) the change in diameter Δd1 of the aluminum rod.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
At a temperature of 20 °C there is a gap ∆ = 0.2 mm between the lower end of the brass bar and the slab rigid suspended from the two steel bars. Neglecting the mass of the slab, determine the stress in each bar when the temperature of the assembly rises to 100°C Answer: σsteel = 15.462MPa (t), σbronze= 20.615MPa(c),
A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm. it fits without clearance in an 80-mm hole in a rigid block. The tube is then subjected to an internal pressure of 4.00 MPa. Assuming v=1/3 and E= 83 GPa, determine the tangential stress in the tube.
Three steel rods (E5 29 3 106 psi) support an 8.5-kip load P. Each of the rods AB and CD has a 0.32-in2 cross-sectional area and rod EF has a 1-in2 cross-sectional area. Neglecting the deformation of bar BED, determine (a) the change in length of rod EF, (b) the stress in each rod.
Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 18 ksi and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD. Take P = 148 kips.The smallest-diameter rod that can be used for member BD is in.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid circular rod of 0.75-in. diameter and P= 5000 lb, determine the normal stress in CG. 3 ft H O D B E F The normal stress in CG is P -4 ft4 ft 4 ft ksi. G. Please type answer note write by hend.