Q8b. The beam section below is solid and homogenous and has the following dimensions:b1 = 65 mm (top flange width), b2 = 65 mm (bottom flange width) and b3 = 25 mm (web width).d1 = 175 mm (section depth), d2 = 25 mm (top flange depth) and d3= 30 mm (bottom flange depth).For the solid homogeneous beam section shown below, determine its centroid coordinate y relative to the origin (0, 0) of the x-y axes. Give youranswer for y in millimetres (mm) to two decimal places.|[d2|b3di[d3b2Answer:

Answered: Image /qna-images/answer/b56e7e63-07f2-46a5-bbd6-75a8d03e39a8.jpg

di = 175 mm (section depth), d2 = 25 mm (top flange depth) and dz= 30 mm (bottom flange depth). For the solid homogeneous beam section shown below, determine its centroid coordinate y relative to the origin (0, 0) of the x-y axes. Give your answer for y in millimetres (mm) to two decimal places.

di = 175 mm (section depth), d2 = 25 mm (top flange depth) and dz= 30 mm (bottom flange depth). For the solid homogeneous beam section shown below, determine its centroid coordinate y relative to the origin (0, 0) of the x-y axes. Give your answer for y in millimetres (mm) to two decimal places.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.7.12P: A simple beam ACE is constructed with square cross sections and a double taper (see figure). The...

See similar textbooks

Related questions

Q: how far the sound travels

A: Here we need to find total distance of sound travels.

Q: The spring is compressed and the piston/cylinder system is in equilibrium. The force due to the spri...

Q: T

A: Given Data : Planes QRS and TUV

Q: The continuous cable that wraps around the small pulleys at A, B, C, and D has a length of 8m. The s...

A: Angle theta and tension in the continuous string.

Q: A nozzle of 50 mm dlameter dellvers a stream of water al 20 m/sec perpendicular to a plate that move...

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 15 cm respectively. The li...

Q: The in-cylinder pressure of an engine has been measured at both TDC and BDC, which are P1 = (1.0000x...

Q: El. 84 m D EL 22.6 m A 0.30-m Ø El. 2.8m

Q: Determine the forces acting in members A, B and C for the truss framework structure below when a 200...

A: Using method of joints to determine the forces in each member.

Q: P- P ot 200 mm C 250 mm S00 mm 550 mm Act Given: Beam AB - 75mmx100mm Beam CD - 50mmx50mm P- 8kN W =...

Q: Determine the resultant of the parallel noncoplanar force system, as shown in the figure, and calcul...

Q: An N13 (0.10in) piano wire compression spring has an outside diameter of 1 in, a free length of 4 in...

A: Fatigue safety factor is the variable of wellbeing concerning an exhaustion disappointment at a give...

Q: The wood beam has a rectangular cross section in the proportions shown. Determine its required dimen...

Q: Problem # 3, at 15.85 °C and 101.3 an air - wate vaper @ saturatin 350 kilo pascal the liguid mistur...

A: Calculate the total pressure of final mixture. Pv=160+1.8=161.8 kPa

Q: 3. Link AB is rotating at a rate of 6 rad/s constantly CCW. Determine the angular velocity of links ...

Q: Question No. 1:A cylindrical specimen of stainless steel having a diameter of 12.8 mm and a gaugelle...

A: Given Data : Diameter of stainless steel specimen = 12.8 mm Gauge Length = 50.8 mm The given data ar...

Q: A meteoroid is speeding through the atmosphere, traveling east at 21.7 km/s while descending at 12.3...

Q: A nozzle of 50 mm diameter delivers a stream of water at 20 m/sec perpendicular to a plate that move...

A: We have to find: 1) The force on the plate 2) The work done 3) The efficiency of the jet We have, d=...

Q: 6. Assuming that the wind force reverses in direction, the maximum service load based on a combined ...

Q: 2. To perform a Kruskal-Wallis test, (a) first rank the observations y, in ascending order and repla...

A: The correct option is A. In the Kruskal-Wallis test first we need to arrange data in ascending order...

Q: 5.1 Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached...

A: Given: A bar with negligible weight one end is supported by ball and socket joint other end is suppo...

Q: The parabolic velocity distribution in a channel flow is given by u(y) = 0.2(1 − y^2) m/s with y mea...

Q: This country's population in 2010 will be (Type an integer or decimal rounded to one decimal place a...

A: Find the population of country ( 2010)

Q: The dimensions of an l-beam are shown in the parameter table below. Find the area moment of inertia ...

Q: *12–4. A particle travels along a straight line with a constant 10 ft, acceleration. When s = 4 ft, ...

A: Answer: The velocity as a function of position is : V = [ (9.17•s) - (27.67) ]0.5

Q: 2. The large piston in a hydraulic lift has a radius of 250 cm2 . What force (kgf) must be applied t...

A: The mentioned unit is in cm2 therefore it is area not radius

Q: 5.00 2.00 МОMENT OF INERTIA 4.00 4.00 1.50 3. Locate the 1.00 centroid of the 1.00 shaded figure. 8....

Q: What is the maximum possible value of theclamping force C in the jaws of the pliers shown inthe figu...

A: Given; The diameter of the pin = 5 mm The ultimate shear stress = 340 MPa The factor of safety = 3

Q: A volume of 0.01 L of water at 60°C is maintained in a cylinder 110 mm in diameter. A 95.86 kg pisto...

Q: How do you calculate the heating surface of a boiler?

Q: If the beam is subjected to a bending moment M = 50 kN-m, determine a.) the maximum bending stress ...

Q: 1.Explain the different methods of measuring pressure ? 2.Describe the different pressure measuring...

A: 1. different methods of measuring pressure 2. different pressure measuring instruments

Q: 1. Calculate the distance a laborer can push a 20.0 kg cart, with a 62N force at 30.0° horizontal an...

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked . K...

Q: Q14a. If the resultant vector force (R) acting on body P is 225 N at 50° relative the x-axis, and F1...

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb. D...

Q: A vertical cylindrical continuous decanter is to separate 44 gal/min of a liquid petroleum oil from ...

A: given data:

Q: A connecting link, 160mm in length, is 50mm in diameter for a length of 100mm and 30mm in diameter f...

Q: The frame shown in Fig. 2 consists of a rigid member CBD and a flexible cable AB. If 80 KN is applie...

A: P=80kN To find displacement at point D

Q: For a drilling operations, the feed per revolution is 0.08 mm / rev and the spindle speed is 7,683.0...

Q: An N-degree of freedom system with no repeated natural frequencies will have O N resonances O 1 reso...

A: Resonance occurs when the frequency of the system becomes equal to the natural frequency of the syst...

Q: how to calculate water friction head loss given data : Tower tank height = 110 M volume of tank = 20...

A: Head loss alludes to an estimation of the energy disseminated in a liquid framework because of conta...

Q: When using a fuel injector pulse tester, Technician A says that little or no pressure drop indicates...

Q: Example/ A slab of steel in circular section with diameter 0.02m ane length 0.4m exposed into a tens...

Q: Part C Figure < 1 of 1 Determine the shear stress Tzz that acts at point A Express your answer to th...

A: Given data as per question Force in x-direction =1300N Force in y-direction =615N Considering FBD of...

Q: shown in Fig. P2.4-3. (a) Plot a curve of engineering stress, o, versus engineering strain, e, using...

Q: Q. A cantilever, 2.5 m long carries a UDL of 20 kN/m. The breadth of the section remains constant an...

Q: For the log brace shown, select the set of Free Body Diagrams that would be used to solve for the te...

Q: total change of entropy.

A: Find total change of entropy.

Q: A sliding block C moves along a horizontal line Q2C. A rotation arm Q2B is 4 feet & 3 in. long and r...

Q: 3. A model for an airplane's pitch loop is shown below. find the range of gain K that v Can the syst...

Question

Q8b. The beam section below is solid and homogenous and has the following dimensions:
b1 = 65 mm (top flange width), b2 = 65 mm (bottom flange width) and b3 = 25 mm (web width).
d1 = 175 mm (section depth), d2 = 25 mm (top flange depth) and d3= 30 mm (bottom flange depth).
For the solid homogeneous beam section shown below, determine its centroid coordinate y relative to the origin (0, 0) of the x-y axes. Give your
answer for y in millimetres (mm) to two decimal places.
|[d2
|b3
di
[d3
b2
Answer:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Detailed calculation

VIEW

Final solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An I section symmetrical beamhas 200mm wide flange and overall depth of 500mm. Each flange is 25mm thickand the web is 20mm thick. Determine the maximum bending moment that should be imposed in the sectionif the tensile or the compressive stressis not to exceed 40MN/m^2 and what percentage of the moment is resisted by flange or web?
1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shear in kN. 3. Determine the location of Neutral Axis, in mm, from the top of the section. 4. Determine the location of the centroid, in mm, from the left of the section. 5. Determine the moment of inertia of the section in x106 mm4 . 6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa. 7. Determine the maximum flexural stress experienced by the beam in MPa. 8. Determine the maximum shearing stress in MPa at Neutral Axis. 9. Determine the spacing of rivets in mm. 10. Determine the maximum flexural stress at 1 m from the support at D to E in MPa.
For the beam and loading shown, use discontinuity functions to compute(a) the slope of the beam at C (positive if counterclockwise and negative if clockwise).(b) the deflection of the beam at C.Assume LAB = 210 mm, LBC = 140 mm, LCD = 120 mm, LDE = 260 mm, MB = 200 N-m, P = 1080 N and a constant value of EI = 590 × 106 N-mm2 for the beam.
A cantilever beam is subjected to a concentrated load of 2000N. The cross sectional dimensions of the double-tee beam are shown. Determine (a) the shear stress at point H, which is 17 mm below the centroid of the double-tee shape, (b) the shear stress at point K, which is 5 mm above the centroid of the double tee shape, and (c) the maximum horisontal shear stress in the double tee shape.
Considering a uniform beam of 1 m long simply supported at both ends, theBending moment is given by the following relation:
Compute the initial deflection of the beam at midspan under service loads with the following specifications: f'c = 4000 psi, 36-inch height, depth of rebar assumed to be 3 inches less than the height, 16-inch width, 4 #9 bars (tension), Grade 60 rebar, 30' clear spans, service loads of: DL = 0.25k/ft, LL = 1.2k/ft. The DL does NOT include self-weight of the beam or of the precast concrete deck planks that have a weight of 60 PSF. The beam picks up a tributary width of 12 feet. Also, note that this beam is continuous and is the middle beam of 5 equal spans. Check the initial deflections against the ACI deflection requirements. Then calculate the long-term deflections and check those against the ACI requirements. For both situations, assume that finish materials will be attached to the beam. Last: Instead of performing a structural analysis to determine the maximum deflection in the beam, conservatively figure that the maximum deflection will be 60% of what it would have been for a…
A simply supported beam is subjected to a uniform service dead load of 1.2 kips/ft (including the weight of the beam), a uniform service live load of 1.8 kips/ft. The beam is 40 feet long, and it has continuous lateral support. If A992 steel is used, and the live load deflection must not exceed L/360, Is a W30 x 99 adequate? (for moment, shear, and deflection).
Determine the most critical point of the beam shown below in terms of bending moment.
Select a W- shape beam limited to a maximum depth of 23.50 in for a span of 40 ft. A 50 ksi steel is used, and the beam is assumed to have full lateral bracing for its compression flange. The nominal loads are a uniform dead load of 0.45 kip/ft and a uniform live load of 0.75 kip/ft.
Calculate the modulus of section of rectangle beam of breadth 120 mm and height 200 mm.
Since the load state and the rectangular cross section of the horizontal beam element are 200 MPa, the shear stress value is 200 MPa;What is the safety beam section (bx2b) value?
The beam is shown in Fig. a has a cross-sectional area in the shape of a channel, Fig. b. Determine the maximum bending stress that occurs in the beam at section a–a.