Given RLC circuit in Figure 3 below with input signal, v(t) = 10 u(t) Volt , R100 kn, L = 100 mH and C = 250 µF.[Diberi litar RLC dalam Rajah 3 di bawah dengan isyarat masukkan v(t) = 10 u(t) Volt ,R =100 kl ,L = 100 mH dan C = 250 uF.]%3D%3DRLv(t) (+i(t)Figure 3[Rajah 31Y(s)(b) Determine the transfer function ofwhere X(s)is input signal and Y(s) isX(s) *voltage across inductor.[Tentukan rangkap pindah bagiY(s)di mana X(s) adalah isyarat masukkan dan Y(s) adalahX(svoltan merentasi induktor.]

In this question , we will find transfer function where output is taken across inductor and input is…

[Diberi litar RLC dalam Rajah 3 di bawah dengan isyarat masukkan v(t) = 10 u(t) Volt ,R = 100 kl ,L = 100 mH dan C = 250 µF.] %3D R L v(t) i(t) Figure 3 [Rajah 31 (b) Determine the transfer function of Y(s) where X(s)is input signal and Y(s) is X(s) voltage across inductor. Y(s) [Tentukan rangkap pindah bagi voltan merentasi induktor.] di mana X(s) adalah isyarat masukkan dan Y(s) adalah X(s)

[Diberi litar RLC dalam Rajah 3 di bawah dengan isyarat masukkan v(t) = 10 u(t) Volt ,R = 100 kl ,L = 100 mH dan C = 250 µF.] %3D R L v(t) i(t) Figure 3 [Rajah 31 (b) Determine the transfer function of Y(s) where X(s)is input signal and Y(s) is X(s) voltage across inductor. Y(s) [Tentukan rangkap pindah bagi voltan merentasi induktor.] di mana X(s) adalah isyarat masukkan dan Y(s) adalah X(s)

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

Q3. Determine the waveform of the output voltage Vo in the network efficiently for sinusoidal input signal Vi shown in Figure 3. Apply ideal diode model for solution. Hint: Show your calculation for each of the positive and negative half cycle and Draw the output voltage with respect to input voltage. X = 7; Y = 0
Choose the correct answer 1. Common emitter configuration of BJT is a a) Current Amplifier b) Voltage Amplifier c) Both a and b d) None of the above 2. Common base configuration of BJT is a a) Current Amplifier b) Voltage Amplifier c) Both a and b d) None of the above 3. Function generators and AC source in Multisim are a) Similar in nature b) Function generators can generate more waveforms while AC source is a square wave c) AC source is just a 220V, 50Hz wave d) Function generate can generate more waveforms while AC source is a asine wave 4. Common collector configuration of BJT is a a) Current Amplifier b) Voltage Amplifier c) Both a and b d) None of the above 5. How can you control the output voltage of a common emitter amplifier BJT a) By RB b) By RE c) By VCC d) By coupling capacitor
Circuits 1 HW 6 Q6
Determine the waveform of the output voltage Vo in the network efficiently for sinusoidalinput signal Vi shown in Figure 3. Apply ideal diode model for solution. Hint: Show yourcalculation for each of the positive and negative half cycle and Draw the output voltage withrespect to input voltage.
In the voltage regulator in the image V1=25, Vz=10V, R1=200 ohms and Pz(max)=400mW a) determine IL, Iz, and I1 if Rl =350 ohms
What is the required resolution of an instrument if the product characteristic specification is 10.0 mm +/- 0,08 mm. Please round your answer to 3 decimal places. Ans 1stttt
Which is not true about sample and hold circuit? a. when switch is off, the charge is maintained at the capacitorb. when switch is on, analog input is deposited at the capacitorc. when switch is off the capacitor dischargesd. capactor is the hold circuit
ECETopic: Thyristor3. What is the difference between 2N6505 and 2N6508 SCR?
Convert the circuit from a T to a pi configuration
16. An RTD has α0 = 0.0035 /oC at T0= 50o C and Resistance R(T0)= 300 Ω . Determine the resistance at 20oC.
A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).
Define α and β. Find IC if α dc =0.98 and IB=40 µA