Answered: Do the following addition and…

Do the following addition and subtraction in 8-bit signed 2's complement. a. 19 - 15 = 10 b. 1915 10 c. 25-37 10 10 = 10 10 d. 12-610 e. 45 +27 10 10 = = =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Find ix using superposition.

A: The current ix is ix= -0.75 amps.Explanation: SUPERPOSITION THEOREM:In any linear active bilateral…

Q: Design a ladder program to run the material mixing system according to the following information: 1-…

A: Inputs I0.0 Start PB I0.1 Stop PB Outputs Q0.0 Pump 1Q0.1 Pump 2Q0.2 Mixer Motor Q0.3 Drain Valve…

Q: Convert the following hexadecimal numbers to binary, octal, and decimal. a. C1D.9 b. 3F.216 c. 57.3…

A: According to the question, we need to convert the given hexadecimal numbers to binary, octal, and…

Q: Suppose we want to compute the OR of R1 and R2, and put the result in R3. Fill in the missing binary…

A: Given that, the binary codes are,The objective is to find the OR operation between and .

Q: Determine Vo and Ip for the circuit in the Figure below +20 V Si Si V www 4.7 Q

A: Refer to the given figure, the diodes are silicon type diodes. Therefore,The forward voltage drop…

Q: Q1) You are asked to use the Arduino UNO development board to control different brightness of the…

A: Details solution is given below Explanation:Step 1:Here the LED can be connected to any PWM ins of…

Q: Sketch the Current through through cach Zenner diode 7v+ "Δ 1042 www 3v 5K2 Sve #2.5v

A: Zenor diode

Q: Required information A 110-V rms, 60-Hz source is applied to a load impedance Z. The apparent power…

A: RMS (Root Mean Square) current is a measure of the effective or equivalent continuous current that…

Q: A 3-phase, 6-pole, 25 Hz, Y-connected AC generator has a stator with 48 slots, each slot contains 20…

A: To calculate the speed of rotation of the stator magnetic field in RPM (Revolutions Per Minute), we…

Q: Look for Requivalent(Equivalent Resistance).Please show details

A: In this question, we need to determine the equivalent resistance across the terminals a and b. Here…

Q: Q3\ Draw the symbols of the following electronic devices. 1- Resistor, 2- Diode, 3- polarized…

A: In the given question we need to draw the circuit symbol for the following electrical elements.

Q: HW7.2 (LTI Processing of Periodic Signals) Consider a periodic, discrete-time sig- nal x : Z → R…

A: Given information:

Q: 1- When a mean optical power is lunched into an 8 km length of fiber is 12 μW, the mean optical…

Q: 3 V Given R1 = 6k, R2 = 4k, address following questions/tasks: (1) Which diode is forward biased, D1…

A: The circuit diagram,

Q: I want to know how to solve equation 1 into equation 2.

A: The step by step explanation of simplifying the equation 1 to get the equation 2 needs to be…

Q: 17. Draw below how to wire a 3-way switch:

A: 3-way switch - Three-way switches are typically used to operate a single light fixture from two…

Q: for the circuit shown in the figure, plot the output voltage waveform and present the resolution in…

A: Explained the answer in brief.youbcan check it.Explanation:

Q: A single-phase transformer with rating of 50 kVA has iron loss of 400 W and full-load copper loss of…

A: The KVA rating of the transformer, The iron loss, The copper loss,

Q: Q2) In the circuit shown in Fig.1, calculate the saturation current and the cut off voltage if…

Q: Find the inverse Laplace transform of: 6s2 +8s +3 (a) F₁(s)= ss²+2s+5)

A: Given that,The objective is to find the inverse laplace transform for .

Q: Find the transfer function of the block diagram given in Figure 2. (Show all the intermediate steps…

A: The transfer function of the given block diagram needs to be calculated and the same can be…

Q: A monopole antenna has a gain of 4.77 dB, is supplied with a 4MHz signal with a current of 10A…

A: Since you have posted a question with multiple sub parts, we will solve the first three sub parts…

Q: Given load current lload 32.5 Amp with 0, 31.8°, and load voltage Vload 135 V with e₁ = 0°. Find the…

Q: This is a very interesting problem that I've encounter and I would like some guidance that would…

A: 1: Establish Transfer Function Gv(s) F(s)=m⋅Vz(s)Where m is the mass of the system. Taking Laplace…

Q: The network shown in the figure below is assembled with uncharged capacitors X, Y, and Z, with Cx 7…

A: In this question, we need to determine the voltage across the capacitor X and Y. We know, charge on…

Q: A generating station has an overall efficieney of 15% and 0-75 kg of coal is bumt per kWh by the…

Q: Calculate v0(t) in the circuit.

A: The voltage V0(t) for the given circuit has been calculated . Final answer will be…

Q: Consider a w-N weight suspended by two wires as shown in the accompanying figure. If the magnitude…

A: The objective of the question is to find the weight (w) suspended by two wires and the magnitude of…

Q: A 12 volt battery is connected to a series circuit in which the inductor is 1/4 Henry and the…

A: Resistor (R):The resistor in the series circuit introduces resistance to the flow of electric…

Q: 2.9. (Fig. 2.21) Data: U11125 V, R11=79, XL1 = 24 92, 12 = 6,5 A, R₂ = 12 2, XL2 = 492, Xc2 = 20 2.…

Q: 1. At 20.0°C, the carbon resistor in an electric circuit connected to a 5.0 V battery has a…

Q: Calculate the value of i at steady state when (a) w = 1 rad/s, (b) w = 2 rad/s and (c) w = 4 rad/…

A: Given Data:The following values of angular frequency are given,Required:Here, the current needs to…

Q: Q2\ fill in the blanks. 1- There are three types of thermistor ..... and

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: Please help ...

A: The objective of the question is to calculate the load voltage and the ripple voltage across the…

Q: What type of fault is shown on the faulted network, and what is the phase rotation of the system?

A: In the given questions we need to explain about the phasor given.

Q: Consider the circuit diagram below. What is the power factor of the circuit? Is it leading or…

A: PF= 0.972 leadingPower factor triangle drawn and attachedP= 3.15W, Q=-0.76 VAR, S= 3.24 VAangle…

Q: 2. Sketch the output voltage, vo(t), for the circuit below for 0 ≤ t≤ 10 ms. vi(t) is given in the…

A: A diode is a semiconductor device with two terminals, an anode, and a cathode. It allows the flow of…

Q: Four capacitors are connected as shown in Figure P16.33 (C = 17.0 ÂµF). C 3.00 µF HH 20.0 F HH 6.00…

A: The given circuit is⇒C=17.0 μF.We need to determine a. The equivalent capacitance between points a…

Q: A wire of diameter 0.900 mm and length 50.0 m has a measured resistance of 1.20 2. What is the…

A: The resistivity of the wire based on the given specifications needs to be calculated.

Q: 09.5

A: option 2 is correctExplanation: Thank you

Q: just part b and c

A: (b) Equilibrium electron and hole densities at 300 K and 600 K: For silicon:…

Q: Compute the discrete-time Fourier transform of the following signal: x[n]=u[n]—u[n—3]

A: The given signal is,Express the signal in simple form as,

Q: Exercise 16-2: Find the form of the natural response of v(t) for the circuit below. 30 ΚΩ 1 μF + 20…

A: Network theory

Q: Answer in 3 decimal please

A: Given:we need to find:equivalent resistance between the terminals A and B.

Q: 9. In dwelling units, hallways ? or more in length shall have at least one receptacle outlet.

A: In dwelling units, hallways 10′ or more in length shall have at least one receptacle outlet.

Q: pose that the electrical network shown below is initially open - no currents are flowing. Assume…

A: In the given questions we need to calculate the mesh current.

Q: πT cos (2000t-7) is(t) = A₁ ⋅ cos (1000 + 727) + A2. cos ( Assume the system is in steady state.…

A: Steady state refers to a condition in an electrical circuit where all voltages, currents, and other…

Q: 8. In the circuit below, determine the node voltage Vд using node voltage analysis. The 60 V…

Q: For the current waveform shown below: A. If A and B = 15.30 A, the average value of the current is _…

Q: 10. Consider the (7,4) systematic cyclic code with generator polynomial g(x)=x³+x+1: a) Use the…

A: Consider the (7,4) systematic cyclic code with generated polynomial g(x) = x3 + x + 1:a) Use the…

Concept explainers

Up-down counter

In digital logic and computing, a counter is a device that stores (and sometimes displays) the number of times a particular event or process has occurred, often in relationship to a clock. A sequential digital logic circuit is the most common type with an input line or clock and multiple output lines. In the binary or binary-coded decimal (BCD) number system, the values on the input line represents a number by several flip-flops connected in a cascaded manner. They are manufactured as separate integrated circuits and are widely used components in digital circuits. These are also a part of larger integrated circuits. These are a specific type of sequential circuit like registers or the value of the flip-flops serving as the output.

Question

Do the following addition and subtraction in 8-bit signed
2's complement.
a. 19 - 15 =
10
b. 1915
10
c. 25-37,
10
10
=
10
d. 12-610
10
=
=
e. 45 +27=
10
10

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculate the addition and subtraction

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 19 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1) Design a counter that has clk and rst as input and 4 bit output. The counter counts in the following sequence: 2-5-8-11-14-1-4-7-10-13-0-3-6-9-12-15
1. Convert 859 and 504 to BCD2. Find the binary equivalent of 10910 and 20383. Find the gray code equivalent of 2 above4. Find the binary equivalent of 10010101 and 111001 if the data is in gray code5. Find the parity bit if 1011100 and 1001001 are transferred using odd and even parity
12: What is the difference between the XOR gate and the X-NOR gate? xor gives two outputs while x-nor gives one both are same xor and x-nor are complement of each other xor gives one output while ex-nor gives two 13: Find the binary equivalent of the given hexadecimal number (4D2.9BF)16 10011010010.100110111111 11001001001.110101011010 11001001011.110011110010 10010101010.0110110001110 14: On multiplication of (11.01) and (01.10), we get ____________ 110.001 011.001 100.1110 01.001 15: The gates required to build a half adder are a. EX-OR gate and OR gate b. EX-NOR gate and AND gate c. EX-OR gate and NOR gate d. EX-OR gate and AND gate 16: The AND-OR implementation of PROM is having fixed AND array and fixed OR array Programmable AND array and fixed OR array fixed AND array and Programmable OR array Programmable AND array and Programmable OR arr
Determine the output of the binary-weighted resistor D/A, if the waveforms representing a sequence of 4-bit binary codes are applied to the inputs. The least significant bit (LSB) is Do with 240 k2 resistance, 5V input, and Rf=20 kN. Find the output of [1101 1001 – 1011 0111]. Calculate the resolution by using a 12- bit D/A convertor.
For a 4-bit full adder circuit:what does the 4-bit adder circuit actually produce if you try to add two numbers whose sum exceeds the 4-bit range of values? Give an arithmetic expression for the unsigned value of the sum bits in terms of x and y input values using the modulus operation
2 DESING A COMBINATIONAL CIRCUIT THAT COMPARES TWO 4-BIT NUMBERS B AND C TO CHECK IF THEY ARE EQUAL. THE CIRCUIT HAS ONE OUTPUT, Z, SO THAT Z = 1 IF B = C AND Z = 0 IF B IS NOT EQUAL TO B.
For Arduino ZERO, using 2.23 V built in reference, what is the input code if the default bit resolution was used for Vin = 1 V?
Find the Binary equivalent of BCD number given below.(0101 0011 0000 . 0111 0101) BCD
From the function below; try solve this by karnaugh map. 1. how many output variables there are?2. what is the value of entry #3 if A is the most significant bit and C is the least significant bit?3. find the minimum function in the sum of products using karnaugh map
Find the binary equivalent of the BCD number (0010 0101 0101.0110 1001 0011)BCD
What is the equivalent 2's complement representation for -15 in 16-bit hexadecimal representation? a) FFFE b) 7FFE c) FFF1 d) 7FF1
Question is below. 1, Draw four-variable Karnaugh Map and find all prime implicants, essential prime implicants. 2,Find simplified Boolean expression for F in SOP form using K-map 3, Implement the simplified Boolean expression using NAND gates only and draw the circuit.