Double U anti-vibration shear mount No. 2. The 16 mm by 22 mm by 25 mm rubber blocks shown in Figure No. 2 are used in a double-U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 285 N causes the upper frame to be deflected downward by 5 mm. Determine Rubber block dimensions Shear deformation of blocks the shear modulus G of the rubber blocks. FIGURE No 2.

Double U anti-vibration shear mount No. 2. The 16 mm by 22 mm by 25 mm rubber blocks shown in Figure No. 2 are used in a double-U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 285 N causes the upper frame to be deflected downward by 5 mm. Determine Rubber block dimensions Shear deformation of blocks the shear modulus G of the rubber blocks. FIGURE No 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
For the built-up shape shown in the figure, determine: a. The location of the plastic neutral axis from the top edge of the flange in mm (ANS 11). b. The plastic section modulus of about the horizontal axis in x106mm3 (ANS 0.214) c. The plastic moment with bending about the vertical axis if Fy = 345 Mpa kN-m. round of to the nearesrt whole number (ANS 43).
Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
Use the siopsdeflction method, dra . axal fors, shear fore, and bending ot dingrams fo the e shown i the fgus. e fre has pi uppors t A e D and constat modlus of lastiiy £). The moments of fneria ) for sach mermbr indicted i the fgure. 1510 1510 | 12 k/m
The 100-mm-diameter pulley shown fits loosely on a 10-mm-diameter shaft for which the coefficient of static friction is Determine the minimum tension T in the belt needed to (a) raise the 100-kg block and (b) lower the block. Assume that no slipping occurs between the belt and pulley and neglect the weight of the pulley Choices: A. TMAX = 1075 N, TMIN = 906 N B. TMAX = 1075 N, TMIN = 690 N
DO NOT GİVE THE CHEGG ANSWER!!!. Do not give the answers given before, because they are not correct, I am giving a downvote :) The cross section of the fixed free-end beam, whose loading condition is given below, is symmetrical with respect to the horizontal axis and the wall thickness t is the same everywhere. According to this;a.) Find and draw the shear flux distribution in the section 1 meter ahead of the free end.b.) How many degrees does the free end rotate?
A simple beam AB supports two concentratedloads P at the positions shown in the figure. A support C at the midpoint of the beam is positioned at dis-tance d below the beam before the loads are applied. Assuming that d 5 10 mm, L 5 6 m, E 5 200 GPa, and 198 10 mm 6 4 I 5 3 , calculate the magni-tude of the loads P so that the beam just touches the support at C.
A rectuangular wooden beam ( fb = 7.0 MPa, E = 12.9 GPa) ha s across-sectional area of300 mm by 600 mm. The beam has a simple span of five meters. A vibrating machine weighing800 kg is located at the midspan. The machine is working under a constant force of 500 N andaccidentally stopped after 0.7 sec (rectangular pulse). Determine the following:Stiffness, ? = _____________________Angular natural frequency, ?? = _________________ Displacement at t = 0.7 seconds ?(? = 0.7) = _______________________Displacement at t = 1.5 seconds ?(? = 1.5) = _______________________(???)? = _______________
Table of values: bf = 1482 mmbw 462 mmt = 292 mm fc' = 28.2 MPafy = 384 MPad = 1011 mmd' = 112 mmL(beam) = 15.1 mW_D1= 48.4 kN/mW_L1 = 56.9 kN/mW_D2 = 184.4 kN/mW_L2 = 208.9 kN/mPROBLEM: A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (W_D1, W_L1)and pair 2 (W_D2, W_L2). The geometric, material and loading properties are all given on thetable above. 1. Solve for the height of the compression stress block using pair 1. 2. Solve for the theoretical steel area using pair 1. 3. Using Es = 0.004, solve for the theoretical steel area using pair 2. 4. Using Es = 0.005, solve for the theoretical steel area using pair 2.
The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 0.4 between both collars and the rod determine the maximum supporting force available from friction when F = 0 and when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 618.75
A tapered cantilever beam AB supports a concentratedload P at the free end (see figure). The crosssections of the beam are rectangular with constantwidth b, depth dA at support A, and depth dB = 3dA/2 at the support. Thus, the depth d and moment of inertiaI at distance x from the free end are, respectively, d = (dA/2L)(2L+x) I=(bd3/12) =(bd3A/96L3)(2L+x)3 = (IA/8L3)(2L+x)3in which IA is the moment of inertia at end A of thebeam.Determine the equation of the deflection curveand the deflection δA at the free end of the beam dueto the load P.