Draw a 3-bit flash converter with Vref= 12 ?. a.Determine the full-scale range. b.Determine the code center for each code.  c.Determine all the transition voltages. d.Determine the resolution

Q: . Determine the truth table of the digital circuit shown in the figure below explain its operation.…

A:

Q: Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO…

A: CPI instruction stands for Compare immediate data with Accumulator. This is a two byte instruction…

Q: PL 102 Gate Control

A:

Q: For a PCM system with the following parameters: Maximum analog input frequency = 4 kHz Maximum…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: How does Arduino microcontroller differentiate an input logic signal 0 to logic signal 1 given a 5V…

A: Microcontroller is a pin device which contains Input/output ports and CPU for processing.

Q: Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted…

A: We need to find out the number of bits per sample and data rate for given pcm signal

Q: 5 What is the conversion time for a 12-bit ADC with a clock frequency of 1 MHz?

A: The solution can be achieved as follows.

Q: In a PCM system, if maximum frequency of the input analog signal is 5 KHz and number of levels in…

A:

Q: Draw the schematic diagram of CRT and label the parts.

A: CRT stands for Cathode ray Tube. The schematic for CRT is shown below.

Q: How many resistors and comparators are required to implement a 10-bit flash ADC?

A: Number of bits in flash type ADC is given, n=10 Number of comparator used in flash type ADC is given…

Q: Determine the signal to quantization noise ratio for a 6 bit PCM.

A: Quantization Noise: The sampled signal with quantization error is the decoder output in a PCM…

Q: For a PCM system with the following parameters, Parameters: (i) Maximum analog input frequency = 5…

A:

Q: If the enable pulse frequency in Figure below were halved, determine the binary numbers represented…

A: Analog to digital converter (ADC) is a device that converts the analog input voltage to digital…

Q: 1- What does the VoH parameter of a logic IC refer to? a) The highest permissible output voltage. b)…

A: VOH  parameter of a logic IC refers to " The lowest output voltage recognized as logic 1 ".

Q: Describe how you would put the digital IO pins of PIC16F877A in input or output mode.

A: PIC16F877A pinout diagram: The PIC microcontroller PIC16F877A is perhaps the most prestigious…

Q: Draw a block diagram of successive approximation ADC and explain its operation briefly.

A: Block diagram of successive approximation ADC

Q: Write a gate level verilog code for Multiplexer

A:

Q: Q1. Design asynchronous (ripple ) binary counter and timing diagram for the following sequence…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 3. Draw the block diagram of an 8255 PPI chip and describe its different programming modes.…

A: block diagram for 8255 PPI is as shown in figure below

Q: - Design a flash ADC with input voltage range [ igital output for a 2.5 V input signal?

A:

Q: Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO…

A: In the 8085 Instruction set, SIM referred to as Set Interrupt Mask. 1-Byte instruction and also…

Q: i. Draw the circuit diagram of 4-bit Ripple Carry Adder.

A: To draw the circuit diagram of 4 bit ripple carry adder 4 full adders are connected one after…

Q: Discuss the difference between Microcontroller & System-on-Chip

A: The microcontroller is used for a specific purpose, various sensors could be interfaced to it while…

Q: 5 Which of the following switching devices are most likely to be used in a three-phase inverter with…

A:

Q: Which circuit is normally used to perform serial-to-parallel and parallel-to-serial data conversion?…

A: Transmitting each bit of a code one after the another from LSB to MSB, is called serial…

Q: What is the maximum conversion time for a counting ADC using a 12-bit DAC and a 2-MHz clock…

A: Given data: fc=2 MHzn=12 bit The expression for the maximum conversion time is given as,…

Q: wave shapes of a three phase inverter

A: Diode- When diode is forward biased it is short circuited in a circuit ideally.When diode is reverse…

Q: For a PCM system with the following parameters: Maximum analog input frequency = 4 kHz Maximum…

A: Given data, Maximum analog input frequency fmax=4 kHz Maximum decoded voltage Vmax=±2.55 V Minimum…

Q: Design a 4 bit binary to double digit 7 segment LED display decoder?

A: According to the question we have to discuss about 4- bit binary to double-digit 7 segments LED…

Q: If Vin exceeded Vref in a real ADC IC, would it actually damage the IC? If not, what would the…

A:

Q: A 16-bit successive approximation ADC is to be designed to operate at 50,000 conversions/second.…

A: Given  Nmax=50,000 conversion/s Calculating conversion time TT=1NmaxTT=150,000 conversion/sTT=2×10-5…

Q: Draw the schematic diagram of CRT and label the parts. B I II

A:

Q: Q:what is the addressing mode for the following instruction: MOV .(C910), A direct mode Relative…

A:

Q: 1- Explain the meaning and operation of CMC instruction ?

A: Since, You ask Multiple questions but we are only allowed to answer one question at a time . so…

Q: frst second 1 00 AA' third 110

A: ASM chart there are three components. They are i) state box, ii) Decision box, iii) condition box.…

Q: Mention what is PDC emulator and how would one know whether PDC emulator is working or not?

A: We have given the following problem Mention what is PDC emulator and how would one know whether PDC…

Q: Find the ratio of maximum conversion time of 8 bit ramp ADC and flash type ADC

A:

Q: Q.19 Draw logic diagram for 4 to 1 line multiplexer. Q.20 Draw logic diagram for 1 to 4 line…

A: Solution: Logic diagram of  the 4×1 multiplexer is given as follows: Where,…

Q: 8085 microprocessor went through its manipulation operation in the ALU, the results was transferred…

A: 8085 is an 8-bit microprocessor which is designed in 1977 by intel using NMOS technology. The 8085…

Q: Q1. Design asynchronous (ripple ) binary counter and timing diagram for the following sequence…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 1. Using the byte rotation scheme described for the ARM7TDMI, calculate the instruction and rotation…

A: The instruction and rotation needed to load the following are determined as shown below

Q: For the ALU circuit shown below, what should be the control word (S251SO) to perform the (sl A)…

A: According to the question, for the given circuit as shown below We need to find the condition for…