Draw the circuit diagram for the following system. The diagram must be neat, legible, and professional in appearance or it will not be marked. You may complete it by hand using a straightedge and circle template or using suitable software such as Automation Studio. Symbols should adhere to those depicted in Appendix D of the textbook. • Electric motor, pressure-compensated pump, suction line filter, pressure relief valve, pressure gauge on pump discharge line. • 4/3 tandem center DCV, solenoid actuated, spring centered. • Two double-acting cylinders connected in parallel using a flow divider positioned after the DCV "A" port to ensure equal flow to the head end of each cylinder. • One pressure-compensated FCV (with integral check valve) in the "A" port line between the DCV and the flow divider to provide extension speed control of both cylinders simultaneously. Rod end lines from both cylinders join together and return to the DCV "B" port.

Draw the circuit diagram for the following system. The diagram must be neat, legible, and professional in appearance or it will not be marked. You may complete it by hand using a straightedge and circle template or using suitable software such as Automation Studio. Symbols should adhere to those depicted in Appendix D of the textbook. • Electric motor, pressure-compensated pump, suction line filter, pressure relief valve, pressure gauge on pump discharge line. • 4/3 tandem center DCV, solenoid actuated, spring centered. • Two double-acting cylinders connected in parallel using a flow divider positioned after the DCV "A" port to ensure equal flow to the head end of each cylinder. • One pressure-compensated FCV (with integral check valve) in the "A" port line between the DCV and the flow divider to provide extension speed control of both cylinders simultaneously. Rod end lines from both cylinders join together and return to the DCV "B" port.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter22: Basics Of Electronics And Computer Systems

Section: Chapter Questions

Problem 4RQ: Means that data concerning the effects of the computers commands are fed back to the computer as an...

See similar textbooks

Similar questions

The automatic washing machine system is an example of ........... loop system.
Suppose that you have designed a portable compressed-air supply system, as shown in the figure below,for filling scuba tanks and for driving pneumatics tools in garages and factories.The system consists of an electric motor, an air compressor, an air tank, a regulator and a pressure-reliefsafety valve.The regulator contains a pressure sensor connected to a power switch. The motor is switched on whenthe tank pressure drops bellow a fixed value and off at a slightly higher pressure. The pressure-reliefvalve is set to open at a higher pressure than the regulator motor off-pressure.Explosion of the tank is clearly a dangerous hazard. Three events are assumed to possibly lead to a tankexplosion:1. an internal tank defect such as poor welding2. an external cause such as a plant vehicle colliding with the tank3. Excess pressure in the tank. The excess pressure can occur only if both the control unit and thepressure-relief valve fail:The pressure sensor might fail to shut oof the motor because…
Which type of control system is used in the given block diagram? Write the definition.
Represent in block diagram form, the control system used in automatic control of speed of a steam turbine.
3. Represent in block diagram form, the control system used in automatic control of speedof a steam turbine.
Is Air conditioner an open loop or closed loop system? Write the reason for your answer. For the Air conditioner system, draw a simple block diagram with the name of input, output and control system used
Identify the following elements of the given closed loop control system.(i) Process Element(ii) Feedback Element (iii) Control Element (iv) Correction Element
An industrial robot performs a machine loading and unloading operation. A PLC is used as the cell controller. The cell operates as follows: (1) a human worker places a part into a nest, (2) the robot reaches over and picks up the part and places it into an induction heating coil, (3) a time of 10 sec is allowed for the heating operation, and (4) the robot reaches into the coil, retrieves the part, and places it on an outgoing conveyor. A limit switch X1 (normally open) is used to indicate that the part is in the nest in step (1). This energizes output contact Y1 to signal the robot to execute step (2) of the work cycle (this is an output contact for the PLC, but an input interlock signal for the robot controller). A photocell X2 is used to indicate that the part has been placed into the induction heating coil C1. Timer T1 is used to provide the 10-sec heating cycle in step (3), at the end of which, output contact Y2 is used to signal the robot to execute step (4). Construct the ladder…
Time constant of thermocouple is 3 milliseconds. An engineer measures the temperature of water and sees that the temperature is less than the real temperature of the boiling water (100 C). How long does the engineer need to wait at least to see the 95 C? 8 milliseconds 5 milliseconds 3 milliseconds none of the given 9 milliseconds not sufficient information
Apply Steady state energy equation
6 Identify the system which is unreliable. a. Open loop and closed loop System b. Open loop System c. None of the above d. Closed loop system
Impulse method