Identify the system which is unreliable. a.

Q: Please explain, in our own words, the difference between the "d operator" and the "8 operator."

A: Both operators are used to represent change in some quantity.

Q: (PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare…

A: Feedback Solution (1): This feedback control starts with a level transmitter that will measure the…

Q: The graph for on-off control mode operation is............

A: The graph for on-off control mode operation is

Q: Which of the following is correct for a open loop system ?

A: The main problem with the open loop control system is that, it do not monitor or check the condition…

Q: ») Explain the basic components of closed loop system shown in figure (a) Error Detector Actuating…

A: A closed-loop control system can be defined as, a system that has a feedback loop (or) a control…

Q: Give a real time example of an open loop system and explain with neat diagram the operation of it.…

A: OPEN LOOP SYSTEM When switch is on, heater heats the element of iron which results in increase of…

Q: Identify the input and output for an automatic refrigerator. Cite instances whether it will be…

A: Temperature control systems (home thermostats) and cruise control systems are two examples of…

Q: Assume Shipping cost per unit between nodes 1 and 2 is $10 and between nodes 2 and 3 is S -30 +10…

A: The Total Demand of Model = 30 +10 = 40 The Total Supply of Model = 30

Q: Represent in block diagram form, the control system used in automatic control of speed of a steam…

A:

Q: 97) In which operating condition is the PCM most likely using the open loop strategy? O Highway…

A:

Q: Which one is not called as classical controller? O a. Programmable logical controller O b. PID…

A: As, we know the most common classical controller is PID controller.

Q: For Industrial Maintence What is defined in Section VIII of an MSDS?

A: What is defined in Section VIII of an MSDS?

Q: xplain the role of feed back signal and error signal in a closed-loop control system

A: Role of Feedback system:- Feedback is taken into account to be a significant part of a closed-loop…

Q: What is the control plane's principal function?

A: Introduction: In a network there are various planes have different works. Every plane or part of…

Q: is an interconnection of components forming a system configuration that will provide a desired…

A:

Q: In the mid-1900s, several technological and analysis concepts came together to make the PID…

A: A PID controller regulates temperature, flow, pressure, speed, and other process variables in…

Q: CTD and BOM are one-to-one related to each other regarding the abstraction levels: False True

A: Solution:   CTD stands for Common Technical Document. BOM stands for Bill of materials.

Q: Schematics are always drawn to show components in their de-energized or off state.

A: Schematics is an electrical or electronic circuit diagram.

Q: The system will have a direct connection between the output and input.

A: Out of the two systems (i) Open Loop System and (ii) Closed Loop System, in Open loop system, the…

Q: The symbol used for output device in PLC is a. Ob. C.

A:

Q: control system is the automation of machine tools that are operated by a programmed command. O a.…

A: Numerical control  is the automatic control of machine tools by means of a computer.A CNC machine…

Q: i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction Element

A: Given: To identify: (i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction…

Q: 10- From the below following, identify the part of the output signal, which is sent back to the…

A: In an open-loop control system, the controlling action is independent of the system output which is…

Q: PID controller is also known as a

A: PID controller is also known as a _Three term Controller__ .

Q: What is system?

A: Given Data : System

Q: Which type of control system is used in the given block diagram? Write the definition.

A: The Control system used in this diagram is open-loop control system.

Q: Which of the following is correct for a open loop system ? O a. No comparison element O b. Automatic…

A: In an open loop system,

Q: Outline the advantages of a PLC system over a traditional control system.

A: PLC - PROGRAMMABLE LOGIC  CONTROLLER  SYSTEM

Q: _________________________________is a type of control system in which the process output is…

A:

Q: What is an interrupt? define and explain how Transfer of Control via Interrupts?

A:

Q: y does a system need to be maintained?

A: we will discuss the need for maintenance

Q: Identify the control system areas of the BMS.

A: Given question: Identify the control system areas of the BMS

Q: b. Identify a real life device/control system configured as Closed-loop Control system and provide…

A: Solution:  A) Open Loop Control system:  A control system in which the control action is…

Q: Determine the controllability and observability for this system

A:

Q: Which of the following is not a criteria in determining the control system performance? natural…

A:

Q: Can an open-loop mechanism be studied as a closed-loop mechanism?  Clearly state How and give an…

A: Given Open loop and closed loop system To find Closed loop as an open loop

Q: Machine Theory Question-3: Determine the degrees of freedom of the following mechanism. Write down…

A:

Q: is an example of Secondary sensing element. The closed loop system does not have feedback signal.

A: LVDT is an example of secondary sensing element.    We know that in the Bordouns tube pressure…

Q: 4 Control technologies which are commonly used in aircraft include: (A) cables, ailerons, flaps,…

A:

Q: In the 1950s, CNC machines used to be programmed and controlled using O A None of the answers B. C++…

A: ANS= PUNCHED TAPE(D)

Q: system can control machines in the real time by executing instruction blocks 15. .. ..... * one by…

A: Direct numerical control (DNC), also known as distributed numerical control (also DNC), is a common…

Q: Why PID controller response is better than P and PI controller response

A: The basic principle behind a PID controller is to read a sensor, then calculate the required…

Q: The role of control element in the closed loop system is

A: Answer:

Q: What is the difference between a closed-loop mechanism and an open-loop  mechanism?

A: We will answer the first question since the exact one was not specified. Please submit the new…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.