Draw the influence line for the force in member BF, then determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 3k/ft and dead load of 2k/ft that acts on the bottom chord of the truss. A -3 ft G -3 ft 3ft F 108 89 E B C 3 ft 3 ft 3 ft 3ft 4 ft D!

Draw the influence line for the force in member BF, then determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 3k/ft and dead load of 2k/ft that acts on the bottom chord of the truss. A -3 ft G -3 ft 3ft F 108 89 E B C 3 ft 3 ft 3 ft 3ft 4 ft D!

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the influence line for the force in memeber HG and BC of the bridge truss shown
Assume that the loads are being transmitted to the bottom of the truss in the diagram below. For members DI and EK, make a chord and create the influence lines. Also, take into account the three-point moving load. a= 5.4 (m) b= 7.3 (m) c= 70 (kN) d= 90 (kN) Determine the following member forces as displayed. Assume the loads are only moving to the right. a. Maximum tension on member DI in kN; if none, enter "0." b. Maximum compression on member DI in kN; if none, enter "0." c. Maximum tension on member EK in kN; if none, enter "0." d. Maximum compression on member EK in kN; if none, enter "0."
For the truss shown in the figure below, assume that the loads are being transmitted to the bottom chord and draw the influence lines for member DI and EK. Also, considering the 3-point moving load as shown, determine the following member forces. Assume that the loads move only to the right. a. Maximum tension on member DI in kN, put “0” if none. b. Maximum compression on member DI in kN, put “0” if none. c. Maximum tension on membe EK in kN, put “0” if none. d. Maximum compression on member EK in kN, put “0” if none. a=5.1m b=6.3m c=62 kN d=78 kN
For the truss shown in the figure below, assume that the loads are being transmitted to the bottom chord and draw the influence lines for member DI and EK. Also, considering the 3-point moving load as shown, determine the following member forces. Assume that the loads move only to the right. a. Maximum tension on member DI in kN, put “0” if none. b. Maximum compression on member DI in kN, put “0” if none. c. Maximum tension on membe EK in kN, put “0” if none. d. Maximum compression on member EK in kN, put “0” if none. a = 5.1 m b = 6.3 m c = 62 kN d = 78 kN
For the truss shown in the figure below, assume that the loads are being transmitted to the bottom chord and draw the influence lines for member DI and EK. Also, considering the 3-point moving load as shown, determine the following member forces. Assume that the loads move only to the right. a. Maximum tension on member DI in kN, put “0” if none. b. Maximum compression on member DI in kN, put “0” if none. c. Maximum tension on membe EK in kN, put “0” if none. d. Maximum compression on member EK in kN, put “0” if none. Note that a = 5.1 m b = 6.3 m c = 62 kN d = 78 kN
For the truss shown in the figure below, assume that the loads are being transmitted to the bottom chord and draw the influence lines for member DI and EK. Also, considering the 3-point moving load as shown, determine the following member forces. Assume that the loads move only to the right. a. Maximum tension on member DI in kN, put “0” if none. b. Maximum compression on member DI in kN, put “0” if none. c. Maximum tension on membe EK in kN, put “0” if none. d. Maximum compression on member EK in kN, put “0” if none. a= 5.1 m b= 6.3 m c= 62 kN d= 78kN
Draw the influence line for the force in member GD, then determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 3 kN/m that acts on the bridge deck along the bottom cord of the truss.
Draw the influence line for the force in member CD, and then determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 800 lb/ft which acts along the bottom cord of the truss.
6. 45 Draw the influence line for the force in (a) member EH and (b) member JE.
2. For the truss shown in the figure below, assume that the loads are being transmitted to the bottomchord and draw the influence lines for member DI and EK. Also, considering the 3-point moving loadas shown, determine the following member forces. Assume that the loads move only to the right.a. Maximum tension on member DI in kN, put “0” if none.b. Maximum compression on member DI in kN, put “0” if none.c. Maximum tension on member EK in kN, put “0” if none.d. Maximum compression on member EK in kN, put “0” if none.
Determine the influence line of the force acting on member GB. Determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 3KN/m that acts on the bridge deck along the bottom cord of the truss.
Draw the influence line for the force in member GD, then determine the maximum tensile force that can be developed in this member due to a uniform live load of 3 kN/m that acts on the bridge deck along the bottom cord of the truss