Draw the ladder rungs to represent: Two switches are normally open, and both have to be closed for a motor to operate Either of two normally open switches has to be closed for a coil to be energized and operate an actuator A motor is switched on by pressing a spring-return push button start switch, and the motor remains on until another spring-return push button stop switch is pressed.

Draw the ladder rungs to represent: Two switches are normally open, and both have to be closed for a motor to operate Either of two normally open switches has to be closed for a coil to be energized and operate an actuator A motor is switched on by pressing a spring-return push button start switch, and the motor remains on until another spring-return push button stop switch is pressed.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter6: Push Buttons And Control Stations

Section: Chapter Questions

Problem 4SQ: Select the best answer for each of the following. A single-break control is a a. heavy-duty selector...

See similar textbooks

Similar questions

A starter turns very slowly and has excessive cranking current draw. When removed from the vehicle and bench tested, the starter spins normally and current draw is within specifications. Technician A says poor battery connections may be the cause. Technician B says an internal engine problem may be the cause. Who is correct?
A single-phase electric motor is connected to a 240-volt, 30-ampere circuit. The motor nameplate indicates that the full-load current draw of the motor is 21 amperes. The motor is connected to an inertia load (a large flywheel) that requires several seconds for the motor to accelerate to full speed. Because of the long starting time, the motor causes the circuit breaker to trip before the load has reached full speed. Your job is to connect a resistor in series with the motor during the starting period that will limit the starting current to 90% of the circuit-breaker rating. An ammeter indicates that the motor has a current draw of 64 amperes when power is first applied to the motor. Determine the ohmic value and wattage rating of the resistor that should be connected in series with the motor during the starting period.
When the start button is pressed, the motor does not start. After a 4 second time delay control relay CR de energizes. Which of the following could cause this problem? TR1 timer coil is open 1m starter coil is open Cr coil is open 2m starter coil is open
quieston 2: Assume all timers are set for 3 seconds. When the start button is pressed, motor #1 starts operating immediately. Motor #2 does NOT start operating after 3 seconds, but after a delay of 6 seconds, motor #3 starts operating. When the stop button is pressed, motors #3 and #1 stop operating immediately. Which of the following could cause this condition? a 2CR coil is open b TR1 coil is open c TR3 coil is open d 2M coil is open
Draw the schematic diagram (power and control circuit) for a 3phase motor starter. When the push button is pressed, the motor starts running on star mode. After 2 minutes of running, the motor runs in delta mode and continues running until the stop switch is pressed.
Select the best answer for each of the following. A single-break control is a a. heavy-duty selector switch. b. single-circuit push button. c. standard-duty selector switch. d. double-circuit push button.
Select the best answer for each of the following. When the reset button does not reestablish the control circuit after an overload, the probable cause is a. the overload heater is too small. b. the overload trip has not cooled sufficiently. c. the auxiliary contacts are defective. d. the overload heater is burned out.
Explain by drawing how intermediate switch is working in ON and OFF position.
Which of the following components would not be connected in series with the contactorcoil A. Compressor internal overload switchB. Low pressure safety switchC. High pressure safety switchD. High discharge temperature safety switch
Select the best answer for each of the following. The purpose of overload protection on a motor is to protect the a. motor from sustained overcurrents. b. wire from high currents. c. motor from sustained overvoltage. d. motor from short circuits.
By using 1 push button NC + 2 push buttons N and two contactors that are activated using DC, draw a circuit for run forward, run reverse, and stop!Please explain clearly
You have 5 push buttons(PB), 2 toggle switches(TS) and 1 lamp. 1. Internal relay #1 will only be energized if PB1 or PB2 is pressed at once or both at the same time while TS1 is ON 2. Internal relay #2 will only be energized if TS2 is ON and both PB3 and PB4 are pressed at the same time 3. Internal relay #3 will only be energized if PB5 is pressed 4. The lamp will only turn ON if both internal relay 1 and 2 is energized. Once the lamp is turned ON, it will only be turned of if Internal relay #3 is energized *Special instruction, turn off TS if the program you reset the program*Make an explanation of how this works.