Draw the output voltage and current waveform of the AC-DC half-wave controlled rectifier feeding the R load. Vs=311.(sin2.n.50.t) V. R=100 ohm. a=45° If a C capacitor with a relatively large capacitance value is connected to the output of this circuit, draw the possible output voltage waveform. olmay

Draw the output voltage and current waveform of the AC-DC half-wave controlled rectifier feeding the R load. Vs=311.(sin2.n.50.t) V. R=100 ohm. a=45° If a C capacitor with a relatively large capacitance value is connected to the output of this circuit, draw the possible output voltage waveform. olmay

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
Consider a peak rectifier ted by a 50 Hz sinusoid having a peak value Vp-100 V. Let the load resistance R 10 kohm. The value of the capacitance C that will result in a peak to peak ripple of 3 V is:
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
1.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. 2.) A 12 V rms ac supply is connected to the primary winding of a transformer with a turns ratio of 0.052. Calculate the rms secondary voltage given a voltage regulation of 4.0% 3.)Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor.
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
Consider the AC to DC converter using half-wave rectifier with the block diagram shown as below. Power transformer + ac line 120 V (rms). 60 Hz + Diode rectifier Filter Voltage regulator + Vo Load v vi The source Us is a sinusoidal input with 12V in RMS value. The diode has the turn-on voltage vp = 0.7V and the load R = 1000. With negligible ripple voltage, the average DC voltage on the load is close to _________ V.
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.