DRAW V AND M DIAGRAM 18 KN 4₁ A ja kN/m 3m Am Im 10 kN/m 3m 777 B

Q: 10–25. Determine the force in each member of the truss. AE is constant. Show primary and secondary…

A: To Calculate-  force in each member of the truss.

Q: 15.6 Solve Problem 15.2 for the loading shown in Fig. P15.2 and a settlement of in. at support B.…

A: Given: E = 29000 ksi=201.3876 ksf I = 1650 in4 = 0.07957 ft4 The settlement, h = 0.5 in  Analyze the…

Q: The beam shown below is a composite beam with the cross section as shown in Figure 3. Segment A is…

A: Given uniformality distributed load = 0.9kip/ft. length = 15 ft.

Q: BUOYANCY: AN INVERTED CONE 10 CM ACROSS THE BOTTOM AND 12 CM HEIGHT  WITH SPECIFIC GRAVITY OF 0.9…

A:

Q: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid…

A:

Q: A 60⁰ B 6 m 5t 60°

A:

Q: The plate is deformed into the dashed shape as shown. If in this deformed shape, the horizontal…

A: L = 303 mm a = 3 mm b = 6 mm  determine the average normal strain along the side AB

Q: stimate the production rate of a D7 bulldozer with a universal blade dozing, dry sand and gravel(CF…

A: Ideal production, Pi = 250 m3/hr loose weight =1600 kg/cu.m Material type: Dry sand and gravel…

Q: Q1 A survey conducted to determine the choice of transportation mode (public bus or private car)…

A: Utility function equation  Um = Bm - 0.45C - 0.25T

Q: 15.6 Solve Problem 15.2 for the loading shown in Fig. P15.2 and a settlement of in. at support B. A…

A:

Q: Using the slope-deflection method, determine the end moments of the beam shown in Figure 11.9a.…

A:

Q: AC10x25 is connected to a gusset plate with 1-inch-diameter bolts as shown in Figure 1. The steel is…

A: 1 in bolt diameter A 572 steel Grade 50 C 10 x 25 ( A = 7.35 in2 , x = 0.617 in , tw = 0.526 in )…

Q: A simply supported beam has a uniformly distributed load of 4N/m. The allowable shear force of…

A: The simply supported beam has uniformly distributed Laod of 4N/m  The allowable shear force of…

Q: Tow super-elented concentric roadway s 5 Separated by a distame of 12.19m between their center…

A: Separation distance between two super-elevated concentric roadways = 12.19m  Radius of Inside Road =…

Q: Express F as a vector in terms of the unit vectors i, j, and k. Determine the magnitude of…

A: The below figure is given;

Q: Determine D10, D30, D60 of the following soils using interpolation. Please show solutions.

A: Soil A Soil B Soil C sieve No. sieve size in mm % finer % finer % finer 4 4.75 84.231 100…

Q: In undisturbed air stream, where the pressure is 14.7 psi and density at standard sea level…

A: V1 = 500 ft/s ; V2= 590 ft/s 1 ft/sec = 0.3048 m/s 500 ft/sec = 152.4 m/s =V1  590 ft/sec = 179.8…

Q: Locate the centroid of the plane area shown below. 90 in 30 in 20 in 70 in 20 in - X

A:

Q: Direction: An activated sludge system (sketched below) is operating at equilibrium with the…

A: An activated sludge system- Flow rate Q=500 m3/hr, BOD=150 mg/L, Effluent BOD=10 mg/L, MLSS=2000…

Q: Explain the procedure for sending individual units through their trials

A: Context: Sending individual units through their trials.

Q: Required: block shear strength of the gusset plate.

A: Plate 6 x 1/2 weld length in shear = 71/2 weld length in tension = 6 in thickness of plate t = 1/2…

Q: List 3 different concepts of Electricity(gravity) not hydro generation using weights design.  Each…

A: Concept 1: Piezoelectricity Generation   Introduction: Piezoelectricity is a concept that…

Q: Part A 174 lb 255 lb 450 lb 356 lb Submit B My Answers Give Up 350 lb The wedge A is used to adjust…

A:

Q: Please provide examples of both successful and unsuccessful traffic engineering projects.

A: The successful Traffic Engineering Projects are those which has roads with managed lanes , proper…

Q: For the frame in method, use Cy as a 500 lb/ft -10 ft- Fig. 1, Determine the reactions at the…

A: Determine the support reaction using force method. (Take Cy as a redundant).

Q: If average distance headway is 25 m, then the basi capacity of a traffic lane at speed of 72 km/h is…

A: Average distance headway S = 25 m, Speed V=72 km/hr,   It is needed to find the basic capacity of…

Q: The absolute maximum Bending Moment in a simply supported beam of span 20 m due to a moving udl of 4…

A: Span of the beam, L = 20 m Moving uniformly distributed load, w = 4 t/m Length of span over which…

Q: (1) What is the flow when avg. speed is 50 mph? (2) A traffic study provided the # of acceptance and…

A: Jam density, Kj=230 veh/mi Free-flow speed, Vmax=65 mph It is asked to determine the following, 1.…

Q: determine the end moments of the beam shown in Figure 11.9a. Assume support B settles 1.5 in, and…

A:

Q: Station 1+100 Station 1+120 Station 1+140 Station 1+160 Station 1+180 Subgrade Cross Sections for…

A:

Q: How is the selection of the site of the small project through degree index systems measurement

A: It is asked to find the selection of the site of the small project through degree index systems…

Q: 3/ Determine the force in each member of the truss and state if the members are in tension or…

A:

Q: 4 years R = 30 cm² Jes (P₂ of Vain fall=130cm, Area = 2500km 2 Find AS

A: Rainfall(P) = 130 cm Runoff(R) = 30 cm3/sec Period = 4 years Area = 500 Km2

Q: The tank is filled with water and kerosene to the depths shown in (Figure 1). The tank has a width…

A: A we have to determine total resultant force

Q: Determine approximately, the reactions at A, B, C, and D. Use portal frame method.

A:

Q: Solve for the maximum deflection if EL= 390,000 kn m^2

A: EI = 390000 KNm2  Determine the maximum deflection in the beam.

Q: Project Location Description CALIFORNIA BEARING RATIO (CBR) TEST Samples Description ASTM D 1883 Day…

A: To find - Swelling Index

Q: 4.) GIVEN THE PHASE DIAGRAM SHOW. WHAT IS THE V₂ Va 3 AIR WATER SOLIDS W= 10% 25=165.416 f1³ 8moist…

A: Moist unit weight (γm) = 127 lb/ft3 Solid unit weight (γs) = 165.4 lb/ft3 Water content (w) = 10% =…

Q: What is the total number of unknowns if determining the reactions at points A, B, C, D, and E? C 250…

A:

Q: for a freeway section, the free-flow speed is estimated to be 55mph. Analysis flow rate is found to…

A: Free flow speed (FFS) = 55mph Analysis flow rate (Vp) = 1500 pc/h/ln

Q: For the given concrete mix design below, calculate the field weight of the ingredients in kg's if…

A: Ingredient Weight in kg/m3 Cement 300 Water 150 SSD Coarse Aggregate 1000 SSD Fine Aggregate…

Q: In a consolidated-drained triaxial test on aclay, the specimen failed at the deviator stress of 124…

A: Deviator stress σd=124 KN/m2 Effective stress friction angle ϕ=31o To find: The effective confining…

Q: Situation 5. Two uniform loads of 123KN/m are acting downward on a concrete pad as shown. The…

A: Note:- Thank you for the question. As the given question is having multiple subparts, so as per the…

Q: PROBLEM: Project Name: Matabanako Elementary School Project Location: Taytay, Rizal Soil…

A: PROBLEM:Project Name: Matabanako Elementary SchoolProject Location: Taytay, RizalSoil…

Q: Problem 3 Complete 5.130 from the course text. 5/130 Determine the shear force V and bending moment…

A:

Q: For the loading on the beam calculate the maximum normal stress due to bending on a transverse…

A: Beam size = 100mm × 200mm  Determine the maximum normal stress due to bending at section C.

Q: As shown in Figure 7, members AC and BD are used to brace the pin-connected structure against a…

A: Factored load, 12 kips. A36-steel properties: fu = 58 ksi fy = 36 ksi

Q: Draw the influence lines for (a) the vertical read (b) the shear at C, and (c) the moment at C.…

A:

Q: Determine the resultant of the three forces and couple by a force-couple system located at point A.…

A: Given figure is as follows; To Find : Resultant of three forces and resultant couple.

Q: Determine the horizontal and vertical displacement of joint C of the truss. The cross-sectional area…

A: E = 150 GPa = 150 × 103 N/mm2  A = 200 mm2  Determine the horizontal and vertical displacement of…