During the measurement of a low resistance using a potentiometer, the following readings were obtained: Voltage drop across unknown resistance = 0.531 %3D Volts. Voltage drop across a 0.1 Ohm standard resistance connected in series with the unknown resistance = 1.083 Volt. %3D Value of the unknown resistor is (a) 49.03 milliohm (c) 20.4 milliohm (b) 108.3 milliohm (d) 53.1 milliohm

During the measurement of a low resistance using a potentiometer, the following readings were obtained: Voltage drop across unknown resistance = 0.531 %3D Volts. Voltage drop across a 0.1 Ohm standard resistance connected in series with the unknown resistance = 1.083 Volt. %3D Value of the unknown resistor is (a) 49.03 milliohm (c) 20.4 milliohm (b) 108.3 milliohm (d) 53.1 milliohm

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 28RQ

See similar textbooks

Similar questions

Answer the following questions: A 0 -150 volt DC voltmeter has a resistance of 100 ohms per volt. What is the instrument resistance? What is the instrument full-scale current? Extend the range of the voltmeter to 750 volts by adding an external multiplier. What is the resistance value, in ohms, of this external multiplier? What is the power dissipation of the external multiplier when the voltmeter is used to measure 750 volts?
1. A PMMC instrument has internal resistance of 1.7kΩ andgives full scale deflection for 50μA. Calculate the required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage ranges of 10V, 50V and 100V.
Look at the images shown. Why can we measure resistance with a pencil drawn on a piece of paper? What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance? 0.449 mega ohms 102.2 kilo ohms
A PMMC instrument has internal resistance of 0.8 kΩ and gives full scale deflection for 33 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 75 V will be __________________ ohms. a. 226.47 b. -360.00 c. 1472.73 d. 93717.00
Two wires A & B made from two different materials have temperature coefficient of resistance equal to 0.0025 and 0.0005 ohm per C , respectively . It is desired to make a coil of wire having a resistance of 1200ohms with a temperature coefficient of 0.001 , using suitable lengths of the two given wires connected in series . Determine the required length of wire A ?
A resistoris measured and found to have a valueof 6066 Ω at 0◦C and 6562 Ω at 100◦C. What are the temperature coefﬁcient and nominal value for the resistor? Assume TNOM =27◦C.
A metallic wire is stretched from original length of 2 m to 5 m. If the original cross-sectional area is 3 square millimeters and original resistance is 7 ohms, determine the new resistance (in ohms) of the metallic wire. Assume the volume of the wire is preserved.
Given circuit, if the ideal ammeter and voltmeter are connected at the same time, what are the values measured by a. I1=? b. I2=? c. Vm=?
Calculate the value of the multiplier resistance on the 50 V range of a de voltmeter, that uses a 200 micro Ampere meter movement with an internal resistance of 100 ohms.
A 0 – 150 voltmeter has a resistance of 2000-ohms per volt. It is desired to change this voltmeter to a 0 – 600 volt instrument by the edition of an external multiplier. What is the resistance, in ohms, of this external multiplier?
Choose the correct option. 1) Semiconductor materials havea) Positive temperature coefficientb) Negative temperature coefficientc) Unpolar temperature coefficientd) has both negative and positive coefficient but depends upon the conditions 2) The temperature coefficient is a a) Device temperatureb) Rise and fall of a temperaturec) Conductivity of a deviced) Rise and fall of conductivity with temperature 3) Electronic and Electrical devices area) Different in nature, principle, weight and power consumptionb) Electronics is a subfield of Electricalc) Works at different voltage levelsd) All of the above 4) Zener diode conducts ina) Forward regionb) Reverse regionc) Both forward and reverse regionsd) None of the above 5) Multisim is a simulation software that has a code for each electrical device it has.a) Trueb) False 6) A solar panel is also the application of a diodea) Trueb) False 7) Forward biasing causes current which is due to thea) minority carriesb) majority carriersc) Both…
OBJECTIVES :1. To identify electrical and electronic components from their physicalappearance.2. To be able to draw the circuit symbol for each of these components.3. To give a physical description and electrical characteristics for each ofthese components.