Answered: E A centrifugal pump with radial vane…

E A centrifugal pump with radial vane tips at the outlet has an in of 100 mm outer diameter. If the rotative speed is 3000 rp olon otric officioncy 0 8 then what is the net head deu frien

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A four stage centrifugal pump in series is required to develop a total manometric head of 640 m when…

Q: A two-lobe rotary positive-displacement pump, similar to that of Fig, moves 3.64 cm3 of tomato paste…

A: Given data

Q: A pump with a design flow of 35m³/hr at 3000 rpm when delivers a head of 50 m. The NPSH, is 3m. What…

Q: 20. A centrifugal pump has an impeller 45 cms in diameter running at 450 rpm. The dischargė at inlet…

A: Given: Impeller diameter D2=45cm or 0.45m (Impeller diameter means diameter of the impeller at the…

Q: Estimate the blade angle at the outlet of centrifugal pump discharging at 125L/s. The pump has a…

Q: The characteristics for a pump are given in the table below. The pump is required to left water…

Q: Discuss the primary difference between positive displacement pump and dynamic pump. Give example for…

Q: Problem #2 A 6AE14 pump with impeller diameter of 12.00 in will be operated at 1750 rpm with a flow…

A: Pump: Pumps are used to deliver liquid from one place to another place having a different height.…

Q: 17. A centrifugal pump hás a 25 cms diameter impeller and an outlet width of 5 cms and runs at 1100…

A: Given: Diameter of the impeller D2=25cm or 0.25m ( Diameter of the impeller means diameter at the…

Q: Determine the recommended minimum speed (rpm) for a radial flow pump operating at 0.165 m3/s of…

Q: A centrifugal pump delivers water against a net head of 14.5 metres and a design speed of 1000…

Q: The performance data for a centrifugal water pumpare shown in Table P14-31 for water at 20°C…

A: Given that :- Volume flow rate (Lpm) =12 Firstly change into m^3 12 L/min = 12 × 10^-3 (m^3) /60…

Q: A Pelton wheel develops 740kW under a head of 310 m. Find the jet diameter if its efficiency is 86%…

A: Given: P = 740 kW H = 310 m efficiency = 86% Cv =0.98

Q: Q3: a: A centrifugal pump used to take water from reservoir to another through 800 m length and 0.15…

Q: A centrifugal pump has vanes which are radial at the outer periphery. The impeller has an outer…

Q: A Pelton wheel has to develop 18000 B.H.P under a net head of 800 m, while running at a speed of 600…

Q: A Pelton wheel is supplied with water under a head of 35 m at the rate of 40.5 kllo Itra/min. The…

A: Here, Head, H=35 m, Q=40.5 kilo/min=40.5 m3/min=40.560 m3/s ϕ=180-160=20°, u=13 m/s

Q: A single acting reciprocating pump has a plunger of diameter 250 mm and a stroke of 350 mm. If the…

A: Introduction: A reciprocating pump is a type of hydraulic equipment that transfers mechanical energy…

Q: A centrifugal pump delivers 60 litres of water per second to a tank situated at a height of 20 me If…

Q: A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow…

A: We are to find the actual head generate by a pump having radial vanes and a manometric efficiency…

Q: An idealized centrifugal pump (blade outer radius of 50 mm) consumes 2 kW power while ru 000 rpm.…

Q: The three-lobe (on each rotar) rotary pump moves 0.145 gal of a coal slurry in each lobe volume…

A: Given data: Slurry displaced per lobe, Vslurry=0.145 galNumber of lobes=3Speed of rotation, n=220…

Q: A centrifugal pump developing 9 ft head at 1200 rpm is driven by a 3 hp motor. Impeller diameter is…

Q: ter is 1025 kg/m³. Calculate (a) the quantity of water flowing through each A tidal km. The…

A: The given problem relates to power generation through tidal energy. There are 140 generators which…

Q: A centrifugal pump has an impeller diameter and width at outlet of 45cm and 8cm, respectively. The…

Q: Example (2-2): Find the specific speed of a double suction centrifugal pump delivering 1.5 m/s…

A: Data given- Q = 1.5 m3/s H = 15 m N = 725 rpm

Q: If a pump discharges 70 GPM of water whose specific weight is 61.5 lb/ff° at local g= 31.9 ft/s,…

A: Given data: Pump discharge = 70 GPM = 70 x 0.133681 ft3/min = 9.357639 ft3/min Specific Weight =…

Q: Velecity of(3amls) A(5 cm) clia im pinges Water Jet with asingle Vane moving in Same. on olivecation…

A: Given: The diameter of jet, d = 5 cm = 0.05 m The velocity of jet, V1 = 30 m/s The velocity of…

Q: 17. A centrifugal pump has a 25 cms diameter impeller and an outlet width of 5 cms and runs at 1100…

Q: A radial flow pump operating at maximum efficiency at a specific speed of 2300 is to deliver 260gpm…

Q: It is desired to deliver 750 gpm at a head of 340 ft. A multistage pump will be used with a rotative…

A: Given- A multistage pump, Discharge required (Q) = 750 gpm Total head required (Ht) = 340 ft N =…

Q: 18. A centrifugal pump has, to work against a head of 25 metres at a speed of 850 rpm.. The flow…

A: Given data: Head against which pump is working, Hm=25 m. Speed of the rotor, N=850 rpm. Flow…

Q: A centrifugal pump impeller delivers 4000 gal/min ofwater at 20 ° C with a shaft rotation rate of…

A: Given, Temperature (T) = 20 °C Q = 4000 gal/min N = 1750 rpm r1 = 6 in r2 = 14 in b1 = b2 = 1.75 in…

Q: 3. A centrifugal pump of 350 mm diameter running at 1000 r.p.m. develops a hcad of 18 metres. The…

Q: A centrifugal pump with radial vané tips at the outlet has an impeller of 100 mm outer diameter. If…

A: Given Do = 100 mm = 0.1 m N = 3000 rpm Manometric efficiency = 0.8 To find Net head magnitude

Q: A centrifugal pump delivers water at a rate of 0.03 m'/sec to a helght of 18 meters through a pipe…

A: We have given data from the question are, Q=30 L/s=301000 m3/s=0.03 m3/sH=18 m,L=90 m

Q: of the pump is 70%. Calculate (a) the developed head of the pump and (b) the total power input. (c)…

A: The water flow rate from reservoir is Q2=60 gal/min×0.003785 m3 1 gal×1 s60 min=3.75×10-3 m3/sec.…

Q: A centrifugal pump has r2 = 9 in, b2 = 2 in, and β2 = 35°and rotates at 1060 r/min. If it generates…

A: Given: Centrifugal pump rotates at N=1060 r/min, head generated is h=150 ft calculating the angular…

Q: A multistage centrifugal pump is required to lift 9000 lit/min from a mine, the total head including…

Q: It is required to deliver 324 gpm against a head of 420 ft at 3600 rpm. Assuming acceptable…

A: Given: water delivered or flow rate of water→Q=324 gpm=0.0026×324=0.842 ft3s Net head of the…

Q: A centrifugal pump has a 25 cms diameter impeller and an outlet width of 5 cms and runs at 1100 Tpm…

A: Head, H=11 mSpeed, N=1100 RPMManometric efficiency, ηman=90%=0.9Vane angle of the impeller at…

Q: Dimension of a centrifugal pump impeller are Parameter Inlet, Section 1 Outlet, Section 2 Radius,r…

Q: A single acting reciprocating pump has a bore of 15 cm and a stroke of 30 cm. The suction pipe has a…

A: Write the given data. D=0.15 mL=0.30 mdsuc=0.10 mθ=30° and 90°N=120 rpm

Q: A given centrifugal pump works at a flow coefficient Cf=0.65 The pump has a diameter of 3.0 cm and a…

Q: A multistage centrifugal pump is required to lift 9000 lit/min from a mine, the total head including…

A: Given that Q=9000 lit/min=0.15 m3/s , total head (H)=500 m;Speed of pump(N)= 2900 rpm , assume for…

Q: 1) A triplex pump with 150 cycl/min strokes and an output pressure of 4000 psig has a hydraulic…

Q: A centrifugal pump with 2.3 diameter impeller running at 327 rpm delivers 7.9 m3/s of water. The…

Q: A centrifugal pump with 2.3 diameter impeller running at 327 rpm delivers 7.9 m/s of water. The head…

Q: A centrifugal pump lifts water against a static head Az = VEN m. The pipe setup has a constant…

A: Given: EN = 62 Δz=62=7.874 m hLS=620.3=3.45 mhLD=3md = 0.15 mw=0.015 mβ2=22°ηh=0.85N= 20*62 = 1240…

Q: A Centrifugal pump is to discharge water at the rate of 110 lits/sec at the speed of 1450 rpm…

A: Answer: The vane angle at outer periphery is 15.616°.

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Q.5 A centrifugal pump with radial vane tips at the outlet has an impeller
of 100 mm outer diameter. If the rotative speed is 3000 rpm and
manometric efficiency 0.8 then what is the net head developed?
part of this bo

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A centrifugal pump developing 9 ft head at 1200 rpm is driven by a 3 hp motor. Impeller diameter is 6-in. Discharge is 1300 gpm. Determine the critical cavitation parameter ?
It is desired to pump 50 ft3/s of water at a speed of 22 r/s,against a head of 80 ft. (a) What type of pump would yourecommend? Estimate (b) the required impeller diameterand (c) the brake horsepower.
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
A fi reboat pump delivers water to a vertical nozzle with a3:1 diameter ratio, as in Fig. If duct and nozzle frictionare neglected and the pump provides 12.3 ft of head tothe fl ow, what will be the outlet fl ow rate?( a ) 85 gal/min, ( b ) 120 gal/min, ( c ) 154 gal/min,( d ) 217 gal/min, ( e ) 285 gal/min
Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Suppose that the axial-flow pump of Fig. with D =18 in, runs at 1800 r/min. (a) Could it efficiently pump25,000 gal/min of water? (b) If so, what head would result?(c) If a head of 120 ft is desired, what values of D and nwould be better?
A centrifugal pump rotating at a speed of 1280 rpm has an impeller with 25cm outer diameter. The vane tips are radial at the outlet. Calculate the net head developed. Assume a value for the manometric efficiency of the pump.
Q6: Calculate the specific speed for the centrifugal pump operates at (3000 r.p.m) & head of (6m) and discharge of (0.2 m3/s).
A Pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400 m. The nozzle diameter is 160 mm and the coefficient of velocity is 0.98, The diameter of the wheel bucket circle is 1.75 m and the buckets deflect the jet by 150°. The wheel-to-jet speed ratio is 0.45. Neglecting riction, calculate (1) the power developed by the turbine, (i) its speed and (i) hydraulic efficiency.
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A centrifugal pump running at 3500 rpm pumps water at a rate of 0.01cu. m./sec. The water enters axially, and leaves the impeller at 5m/s relative to the blades, which are radial at the exit. If the pump requires 5kW, and is 67% efficient, estimate the basic dimensions (impeller exit diameter and width).
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.