Problem-4:The characteristics for a pump are given in the table below. The pump is required to left water againststatic head Az = EN" m. The pipe arrangement has a total length Lthe pump discharge, head, efficiency and power for the given pipe system.200, d = 0.1 m and f= 0.016. Find%3DQ (L/s)102030354250Hp (m)efficiency %2102011801501299348305880858674EN=62Hp = Az + h, = Az +12.1 dP =757

Answered: Image /qna-images/answer/3c27cd75-4902-492a-94f5-87d5b1c21568.jpg

The characteristics for a pump are given in the table below. The pump is required to left water against static head AZ = EN" m. The pipe arrangement has a total length L 200, d 0.1 m and f= 0.016. Find the pump discharge, head, efficiency and power for the given pipe system.

The characteristics for a pump are given in the table below. The pump is required to left water against static head AZ = EN" m. The pipe arrangement has a total length L 200, d 0.1 m and f= 0.016. Find the pump discharge, head, efficiency and power for the given pipe system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the flow configuration shown, you are required to design a pump station to transfer water from the bottom tank to the upper tank. In your own words, explain the steps that are needed to be followed for the design of the pump system. Your answer should be typed and not more than one page. The pipe equivalent roughness is 1.5 mm. And a valve with a k=10 is located just upstream of the lower reservoir (other losses are negligible). Take p=1000 kg/m”, g = 9.81 m/s?, and u = 1.179 x 102 kg/m.s.
A pump with an efficiency of 89.842 percent delivers water at a rate of 13.79 m3/s but with a leakage loss of 0.5 m3/s. The friction losses within the pump result in a 1 m head loss. What is the total dynamic head of the pump in meters if it has a mechanical efficiency of 98 percent?
The below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oiltanker to a refinery storage tank, both free surfaces being open to the atmosphere. Theeffective length—including fittings—of the commercial steel pipe is 6,000 ft. The dischargeat point 4 is 200 ft above the pump exit, which is level with the free surface of oil in thetanker. However, because of an intervening hill, point 3 is at a higher altitude than point 4.Losses between points 1 and 2 may be ignored.The crude oil has the following properties:Density ρ = 53 lbm/ft 3 ; Viscosity μ = 13.2 cP; Vapour Pressure Pv = 4.0 psia Answer the following questions:1. If the combination of pump and motor is 80% efficient, how much electrical power(kW) is needed to drive the pump?2. If, in order to avoid vapour lock, the pressure in the pipeline must always be above thevapor pressure of the crude oil, what is the maximum permissible elevation of point 3relative to point 4?3. If the flow in the pipeline…
Q-- Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
As seen in Figure 3 below, the water from the tank 1 is pumped to the tank 2 with a flow rate of 5,664 liters/s, passing through a pipe with a diameter of 50.8 mm and a length of 121.92 m. Some of the local losses in the system are also shown on the figure. Calculate the effective power of the pump by taking the relative roughness ɛ / d = 0.001 Note: For all questions, pwater = 1000 kg/m³, g=9.81m/s^2 , the kinematic viscosity of water is 1.0219x106 m²/s and the questions can be solved by accepting the values that are not given.
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
The plunger diameter of a single acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10,3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 2.1 Find the maximum allowable speed to operate the pump 2.2 What power is expected in overcoming friction at this speed, take f=0.01
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
Water recirculates at a volume flow rate of 0.4524 ft3/min from the blade outlet to the impeller, and shaft sealing losses are negligible. A centrifugal pump has a hydraulic efficiency of 95% and a mechanical efficiency of 93%, respectively. Calculate the pump efficiency in percent if the pump delivers water at a flow rate of 12 ft3/min.
Given: Two(2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95 Bars Suction Pipe Dia = 450mm Discharge pipe Dia = 480mm Velocity of Water = 4.25 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and Or = Total Flow Rate
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
A radial flow pump operating at maximum efficiency at a specific speed of 2300 is to deliver 260gpm against a head of 129ft at a rotative speed of 2100 rpm. Find the required number of stages. ANSWER: 3