(a) Consider the system shown in Figure Q4 (a).industrial oven is 600 °C. A K-type thermocouple which has its characteristics shown inthe maximum temperature of thethe figure used to measure the oven temperature. The analog-to-digital converter has athreshold value of 2.5 V:(i) Calculate the gain of the amplifier.(ii) If the amplifier used is a non-inverting amplifier with a feedback resistance of 62 kO,calculate the input resistance value.(iii) If the K-type sensor replaced by E-type discuss the minimum changes needed tomeasure the oven temperature.80IndustrialOven604020RK-typeThermocouplesAnalog-to-DigitalConverterAmplifier6001000150020000Temperature "cOven with temperatureThermocouplesmeasurement systemcharacteristicsFigure Q4 (a)millivolts (mV)

Answered: Image /qna-images/answer/b49bdabd-7a4e-46a8-9f04-613e3e6bd325.jpg

(e) industrial oven is 600 °C. A K-type thermocouple which has its characteristics shown in the system snown in Figure Q4 (a). temperature the the figure used to measure the oven temperature. The analog-to-digital converter has a threshold value of 2.5 V: (i) Calculate the gain of the amplifier. (ii) If the amplifier used is a non-inverting amplifier with a feedback resistance of 62 kol, calculate the input resistance value. (iii) If the K-type sensor replaced by E-type discuss the minimum changes needed to measure the oven temperature. 80 Industrial Oven 60 K K 40 20 R K-type Thermocouples Amplifier Analog-to-Digital Converter 600 1000 1500 20000 Temperature C Oven with temperature Thermocouples measurement system characteristics

(e) industrial oven is 600 °C. A K-type thermocouple which has its characteristics shown in the system snown in Figure Q4 (a). temperature the the figure used to measure the oven temperature. The analog-to-digital converter has a threshold value of 2.5 V: (i) Calculate the gain of the amplifier. (ii) If the amplifier used is a non-inverting amplifier with a feedback resistance of 62 kol, calculate the input resistance value. (iii) If the K-type sensor replaced by E-type discuss the minimum changes needed to measure the oven temperature. 80 Industrial Oven 60 K K 40 20 R K-type Thermocouples Amplifier Analog-to-Digital Converter 600 1000 1500 20000 Temperature C Oven with temperature Thermocouples measurement system characteristics

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Assume for a moment that perfectly accurate resistors were available for feedback networks; that is resistor tolerance is 0%. Then any deviation from the value set by the feedback resistor ratio is caused by insufficient raw op-amp gain. What minimum raw gain would be needed to get within 1% if an intended overall gain of 10? What if the intended gain is 100 instead?
a) Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kohm resistor in the feedback path, and +-12 v power supplies. b) Using your design from part a, determine the range of input voltages that will keep the op amp in it's linear operating region. c) suppose you wish to amplify a 2 V signal, using your design from part a, with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
1. Design an inverting amplifier with a gain of 4. Use an ideal op amp, a 30 kΩ resistor in the feedback path, and ±12 V power supplies. 2. Using your design from part (a), determine the range of input voltages that will keep the op amp in its linear operating region. 3. Suppose you wish to amplify a 2 V signal, using your design from part (a) with a variable feedback resistor. What is the largest value of feedback resistance that keeps the op amp in its linear operation region? Using this resistor value, what is the new gain of the inverting amplifier?
Find out the gain of inverting amplifier if it is performing on 12 V supply, it has input resistance of 20 ohm and feedback resistance of 50 ohm respectively. NOTE : KINDLY ELABORATE BRIEFLY
Question 2 Part (A) Design an inverting amplifier with a gain of 4. Use an ideal ops amp, a 30kΩ resistorin the feedback path, and ±12V power supplies. Part (B) Using your design from part (a), determine the range of input voltages that will keepthe op amp in the linear operating regions. Part (C) Suppose you wish to amplify a 2V signal, using your design from part (a) with avariable feedback resistor. What is the largest value for the feedback resistance thatkeeps the op amp in the linear operating region? Using this resistance value, what isthe new gain of the inverting amplifier.
Compare the closed-loop voltage gain, k = Vo/Vs, for the loaded and unloaded dependent source model of the Voltage Follower with the ideal model of the Voltage to examine the impact of the load, RL on k. - Using any circuit analysis method, derive expressions for the closed-loop gain, k = Vo/Vs, for the ideal opamp Voltage Follower ,both the unloaded ,loaded Voltage Follower using the dependent source model. simplify both of the closed-loop gain expressions for the dependent source models by applying the ideal opamp parameters: A --> infinity , R_i -->infinity and R_0 --> infinity.
Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
Q 1) For the given circuit shown in Figure 4.1: (i) Provide the name for this op-amp circuit configuration and use the ideal op-amp assumptions to solve for the output voltage in terms of the input voltages and resistors. (ii) What is the input resistance seen by ?0, V1 and V2. ?
An amplifier has voltage gain with the feedback of 100. If the gain without feedback changes by 409 and the gain with feedback should not vary more than 8%, the values of open-loop gain and feedback ratio will be respectively given by
Suppose the output signal voltage from the amplifier is 35 times the input signal voltage. If the imput and output impedance are both pure resistances of the same value, what is the gain
Consider the feedback circuit shown in Fig. 4, assume that the value of R1 + R2is high enough and λ = 0. a) Determine the open-loop gain by writing A1= (Vx/Vin) (Vout/Vx).A1= b and c parts in the photo
The upper critical frequency of an op-amp’s open-loop response is 200 Hz. If the midrange gain is 175,000, answer the following: What is the ideal gain at 200 Hz? What is the actual gain? What is the op-amp’s open-loop bandwidth?