The longest pipe run for a hot water systemis 100 m. If the pressure rise through thepump is 35 kPa, then the pressure drop perone meter in system isإختر أحد الخيارات:Pa/m 233.3 .a OPa/m 400 .bOPa/m 250 .c OPa/m 375 .d O

ANSWER- 350 Pa/m Which is not given in the Option.

Answered: e longest pipe r

Engineering

Mechanical Engineering

e longest pipe r

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Pr. 1: What is the velocity of the flow of water in leg B of the tee shown in the figure? 4 m…

A: There are 2 figures in the question but only in one figure leg B is shown. Hence I have taken that…

Q: Q2) ) A piping system consists of three pipes arranged in series the lengths of the pipes are…

Q: 20-mm-diameter hose. Draw the energy and hydraulic grade lines for the hose using a datum at B. 0.4…

Q: What is the velocity of the pipe center (m/s)? Given that h3=31.3 cm hy =7 am h= 3 cm Water

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: O N/m. l1=0.4 m and l2=0.6 m. A. Pump

A: data given Motor pump system Mass m =50 kg mass moment of inertia J0 =100 lg/m2 spring stiffness…

Q: Using the diagram, determine the maximum clearance

Q: U méter long met at the rate essure at th

A: given:flow rate Q=4.5m3/hd=0.025m

Q: Which of the ff equations is true regarding the pipe network ? i.Qin = QB + QA ii.QA + QD + QF = 0…

A: To find : Which of the following equations is true regarding the pipe network ?

Q: Write relation of weir structure with flow rate

A: solved

Q: What is the velocity of the pipe center (m/s)? Given that h3=68.9 cm h2 =7 cm h =3 cm Water .

A: given data: difference in head at pitot tube be h; according the question h = h3 h = 0.689m taking,…

Q: What is the velocity of the pipe center (m/s)? Given that h3=47.1 cm hy =7 cm h =3 cm Water

A: Solution:

Q: The hydraulic radius of a pipe with diameter of 12 mm is equal to 3 mm 6 mm 9 mm 4 mm

A: hydraulic radius is the ratio of wetted area (A) to the wetted perimeter (P). i.e. Rh=AP For…

Q: Determine the differential force along Pore section

Q: valuate 5.e + 8e

Q: 8. What is the pressure at the center of the pipe B? The inclined tube makes an angle of 36.9° to…

A: Givenθ=36.9o

Q: hich of the following is turbulent flow according to Reynolds number for pipe? a. Re is less…

Q: c) The increase in the outer and inner diameters Ddout and Ddin d) The increase in the pipe wall…

Q: 7.73 Sketch the HGL and the EGL for this conduit, which tapers uniformly from the left end to the…

A: HGL can be obtained by subtracting the loss due to friction in the pipe line from the static head.…

Q: (10+0.5z) acts e dx in meter. T

Q: In a hydroelectric power plant, water flows through a large tube through the dam. This tube is…

A: In a hydropower plant, dams are used for transforming mechanical energy into electrical energy with…

Q: mine the section modulus -160 mm

Q: Draw Hydraulic Grade Line (HGL) and Energy Grade Line (EGL) and discuss.

Q: quater circle segment gate

Q: a- Reynolds number R,- b- Entry length L,- c- Nusselt number, Nu =

Q: 1-Comment on the differences in reading measurements and whether these differences could be from…

A: Answer:1)i)The accuracy of measurements of readings in flows depends on the fluid properties.ii)The…

Q: FACE TO FACE DIST 44.40 meters Somm gomm gomm USE: 3metes As shown in Figure, a drainage is to be…

A: Write the face to face distance where pipes are going to be fitted. L=44.40 m Write the length of…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: Part(a).From the given print,we can say that section A-A contains several parts.for example-It…

Q: 15m P=08 kN T-12AN

A: Given:- EG = 1.5 i - j +3kP moment about EME = EGXP = 1.5 i - j +3k443.7 i- 665.6…

Q: or venture meter experiment, the aiflerence between the measured pre wrer waslos Kpa). the diometer…

A: Given the weight density = 9.81 Given the pressure = 0.5 kPa Given the diameter of wide pipe = 180…

Q: QUESTION 1 A horizontal well with a measured depth of 10,000 ft. can be approximated as being…

A: Given that, Length of well=10,000 ft,Daimeter of hole, D=8.5 ft,Drillstring OD, d=5 in,Mud weight,…

Q: 6. List the relations and laws that control the connection of branching pipes, and explain the three…

A: Introduction: Pipe flow: Pipe flow is a type of liquid flow that occurs inside a closed conduit,…

Q: 30N/m 0.4kg Wwww

A: For solution refer below images.

Q: A₁-78 cm² and A₂-254 cm². Solve for the loss coefficient. /// //////// //////

A: Given:A1=254 cm2A2=78 cm2

Q: Find the velocity at the pipe center. water D-3" 0.0 (stag.) Hg (S-13.6)

A: Given: Specific gravity of mercury Sm=13.6Reading of the differential manometer (hm)=1inch or…

Q: If the fluid motor has an efficiency of 78 percent, how much power is delivered by the motor? 1-in…

A: Hydraulics and pneumatics technologies are referred to as "fluid power." To transmit power from one…

Q: Question 6 A weir is a barrier that spans across the width of a river and is used to alter its flow…

A: Weir or notch is a opening in the side of a reservoir with upstream liquid level below the upper…

Q: With the given pipe lengths, sizes and connections and if all pipes have an f=0.020. 1. which of…

A: In real life the use of fluid flow in both circular and noncircular pipelines is widespread. The…

Q: |Umax u = u(r) s this flow

A: U=Umax(1-(2yh)2] UMAX=25 cm/s=0.25 m/sviscocity μ=3.5 cp=3.5 x 10-3 N-s/m2area of lower plate ,…

Q: 1) Define the following terms and explain where they are used or applied. *notch *weir *venturi…

A: Solution to first question as per our company policy:

Q: discharged from f curvature of t ow Point A.

A: a) Here , the normal component of acceleration is aAn=g cosθ = (9.8068) cos 50∘…

Q: Define the dimension 3” XS BI pipe

A: 3" XS BI Pipe:- The above designation of the pipe indicates the size of the pipe and type of the…

Q: what is the pressure 20 ?m downstream

A: Given: V1= 1 m/s P1= 3000 Pa To determine: The pressure at downstream

Q: Dsses). Pipe No. D (mm) L (km) C 200 A 0.6 0.5 1.2 0.00 0.022 0.024

Q: ne discharge passing betw

Q: Describe and Draw Energy Grade Line (EGL) &Hydraulic Grade Line (HGL) Describe and write the…

A: given:

Q: Calculate the total loss of the following system. Physical pipe length. 350 f IN- Flanged check…

A: Write the given data Q=500 GPM =0.03155 m3/sd=5''=0.127 m Calculate the velocity of the flow.…

Q: e flow type

A: Flow is laminar.

Q: شرع Find the discharge of water flow .through the pipe in Fig 0.5m (2 D=50mm/ FL-6m EL-4.5m 0.024…

Q: Find the pressure in KN/m2 at the center of pipe A. T = 10°C. %3D Oil (S = 0.85

Q: b. Answer with True (T) or False (F). 1. Relative Roughness may larger than 1. 2. Moddy Diagram used…

A: Relative roughness may larger than 1 Answer As we know that relative Roughness is defined…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

The longest pipe run for a hot water system
is 100 m. If the pressure rise through the
pump is 35 kPa, then the pressure drop per
one meter in system is
إختر أحد الخيارات:
Pa/m 233.3 .a O
Pa/m 400 .bO
Pa/m 250 .c O
Pa/m 375 .d O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the parallel-pipe system of Fig. each pipe iscast iron, and the pressure drop p1 - p2 = 3 lbf/in2. Computethe total flow rate between 1 and 2 if the fluid is SAE10 oil at 20°C.
Calculate the diameter of the vertical pipe needed for the flow of liquid at Re=1600 when the pressure remains constant, ν=1.5 x 10-6 m2 /s. [Ans: D=2.27 mm]"Note: I want the answer with a simple figure."
For the piping system of Fig. , all pipes are concretewith a roughness of 0.04 in. Neglecting minor losses, computethe overall pressure drop p1 - p2 in lbf/in2 ifQ =20 ft3/s. The fluid is water at 20°C.
The difference of mercury level in a differential U-tube manometer connected to the two tapping of the pitot –tube is 100 mm. Take coefficient of pitot tube 0.98 and Soil =0.8. Calculate: i. difference of pressure head (h) ii. entrance velocity (v)
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 108 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument) as 0.9 and sp. gr of oil = 0.8 Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr) =
fLUID MECAHNICS The flow in the piping system shown is 10 mgd. Determine (a) the head loss from A to D and (b) the flow in pipes 2, 3, and 4. Use C = 100 for all pipes. (a) head loss : _____________________ ft of water(b)Flow in Pipe 2: _____________________ mgd Pipe 3: _____________________ mgd Pipe 4: _____________________ mgd
A cast iron pipe is to convey oil with specific gravity of 0.9 and a viscosity of 0.00384 Pa-s from one tank to another at a rate of 14 L/s. If the If the diameter of the pipe is 2.75 m, find the Friction factor. Relative roughness is 0.001.
a) What is the head loss in (m)? b) What is the pressure drop (P1-P2) in (kPa)?
Q.4) Differentiate between major and minor losses in pipes.
pressure different is 2200 kN/m2 and pipe length is 98m
A Pitot tube in a pipe in which air is flowing is connected to a manometer containing water asshown below. If the difference in water levels in the manometer is 10 cm, what is the velocity of flow in the pipe? Assume a tube coefficient of Cp = 0.99, specific weight of air is 12 N/ sq.m.
plzz help mee nowwww What is the pipe pressure (pa)? Given the S for Mercury is 13 and S for fluid =1.3