e voltage is measured

Q: WHAT IS THE TOTAL SIZE CHANGE OF THE AC BAR

A:

Q: True or False: The LENGTHEN command doesn’t work with arcs.

A: While using the LENGTHEN command, the Delta and angle options allows the user to lengthen or shorten…

Q: Details is following Fr=6000N Fa=3000N N=2400rpm Find the total life using data in question.

A: As we know Given Data :- Fr=6000N Fa=3000N N=2400rpm

Q: Explain working principle of hook gauges?

A: Hook Gauge is a mechanical device that used to find changes in water level within an evaporation…

Q: True or False? In a parallel circuit, circuit current is the same throughout all parts of the…

A: Given Data : Parallel circuit

Q: the open circuit voltage and

A: Given; In a DC are welding operation, the voltage-arc length characteristics was obtained as,…

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: B E K Li 4 FDI and FIE are equall to zero Yes No O

A: In the truss structure if three members form a truss joint for which two of the members are…

Q: Water is flowing thru the pipe set-up. What can be the v thru pipe 3 ?

A:

Q: TRUE OR FALSE

A: This is false. According to Newton's relativity theory, the observer on the spaceship is measured a…

Q: O c. 2 None of them

A:

Q: adjustments in dial indicator readings should be made to compensate for?

A: Dial indicator is an instrument used for alignment purposes. The dial indicator is widely acceptable…

Q: should draw a thr u should verify Dc

A: Degree of freedom: It is defined as the number of independent relative motions that a pair can have.…

Q: The unit of distance is not meter. Select one: a. True b. False

A: The unit of distance in the SI unit is the meter and it can be expressed in mm, cm, km, etc. Since…

Q: rance between an alloy that failed at a lo

A: (e) In materials science, weariness is the debilitating of a material brought about by cyclic…

Q: The meaning of Re is

A: This question is based on the concept of dimensionless number from fluid mechanics.

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: Define the following statements which is true ?

A: Given;   Water at 420 C is sprayed into a stream of air at atmospheric pressureDBT=400CWBT=200CAir…

Q: The value of FPQ

A: Given data;  From the given figure, Three sets of parallel plates LM,NR and PQ.   View factor FU is…

Q: Select the right reading of the ?Micrometer Screw Gauge

A: we need to find reading in the micrometer.

Q: What is thermocouple gauge used for detection of leaks in vacuum systems.

A:

Q: e pressure gauge reading?

A: To find Pressure gauge reading.

Q: d2s V= dt2 True False

A:

Q: he height of the air pressure (h2).

A: Need To calculate height of air  pressure. (h2)

Q: 19- In a venturimeter construction, the last (third) part is is called as short diverging part.…

A:

Q: - Which of the following statements regarding a

A: Given; Choose the following statements is correct,  Where,  Rankine cycle with reheating ,

Q: voltage.

A: answer - 267.69V

Q: What is the temperature of low

A: Given; A carnot cycle is having an efficiency of;  ηcarnot=0.75  High temperature reservior;…

Q: The unit of discharge in m3/kg Select one: True False

A: Basic units: Area = m 2 Velocity = m/s

Q: the current (in A) required

A: Given: An electromechanical is to be used to cut through hole into ,Thickness,t=12 mmThe hole has a…

Q: write down what is magnetic sensor

A: a magnetic sensor is basically an electromagnetic device which detects the magnitude of magnetism…

Q: SLPM stands for _______ liters per minute a. speed b. standard c. static d. specific

A: SLPM is a unit of measuring volumetric flow rate of a gas.

Q: What are the Purposes of the following instruments ? Instrument Function | 1. telescoping gauge |2.…

A: To explain The function of the following instruments  telescoping gauge  radius gauge  feeler gauge…

Q: Describe any three uses of the following gauge.

A:

Q: e Taylor's principle with Plug and Ring Gauge with figure.

A: The given problem is based on metrology.    Taylor's Principles: Go gauge should be design on…

Q: Checking the shaft diameter using the Johnson gauge, which type of measurement? O A) Direct…

A: Option (a) is correct. It comes with direct-controlled measurement.

Q: e output voltage of

A: Need to find Output voltages.

Q: An illustration is a picture or diagram .found in a book True False O

A: Option a True There are many types  to explain  illustration. The simplest is  that illustration…

Q: Mark True or False 12- When OLX equals zero, it represents Newton's first law. true Error

A:

Q: True/False. To make electrical energy using solar power, the sun turns a generator. False True

A: Solution:

Q: - 1-why generally the voltage is applied to H.V.side?

A: Voltage is applied to HV side.

Q: °C. What is the distance of zero and 30 mark under these conditions?

A:

Q: want orthographic view of both

A:

Q: if the first digit of the diagnostic trouble code is zero what does it mean ?

A: Diagnostic trouble codes or also known as DTC, are the type of codes used by the vehicle…

Q: What does the voltage measurement across the conductor indicate?

A: Option d is the correct answer. i.e Wire condition cannot be determine.

Q: Which of the following statements is NOT true?

A: Consider option (a) Gas constant R has specific value,R=8.314 J/mol·KHence, R>0 So the option (a)…

Q: A fixed rating pressure switch is adjusted inside the pressure control and display console to record…

A: Pressure switch is a device, used to provide electrical feedback in response to measuring the level…

Q: Which of the following has multiple degrees of freedom? Option 3 O Option 1

A: Multi-degree-of-freedom (multi-DOF) systems are those in which the motion is described by two or…

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.