E2.3 Given a two-input neuron with the following weight matrix and input vector: = [3 2] andp [-5 7]", we would like to have an output of 0.5. Do you suppose that there is a combination of bias and transfer function that might allow this? i. Is there a transfer function from Table 2.1 that will do the job if the bias is zero? ii. Is there a bias that will do the job if the linear transfer function is used? If yes, what is it? iii. Is there a bias that will do the job if a log-sigmoid transfer function is used? Again, if yes, what is it? iv. Is there a bias that will do the job if a symmetrical hard limit transfer function is used? Again, if yes, what is it?

E2.3 Given a two-input neuron with the following weight matrix and input vector: = [3 2] andp [-5 7]", we would like to have an output of 0.5. Do you suppose that there is a combination of bias and transfer function that might allow this? i. Is there a transfer function from Table 2.1 that will do the job if the bias is zero? ii. Is there a bias that will do the job if the linear transfer function is used? If yes, what is it? iii. Is there a bias that will do the job if a log-sigmoid transfer function is used? Again, if yes, what is it? iv. Is there a bias that will do the job if a symmetrical hard limit transfer function is used? Again, if yes, what is it?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Derive an expression for the Thevenin Equivalent voltage source of the 4-bit DAC. The source will be a function of each binary input signal b0 to b3, where the bx can take the value of either 0 or 1. (Find A-D here: VThev=Ab0 + Bb1 + Cb2 + Db3 )
Express the voltage, current, and power gains ,a signalvi = 0.1 sin 2000πt volts Thévenin equivalent source resistance RI of 2 kΩ, and we ’d like to listen to that signal with a 32-Ω ear bud, represented by the load RL , as depicted by the circuit model in dB.
We are now interested in studying the behavior of the rotating valve plate shaft on an ETC only. This is to evaluate the dynan1ic response of the valve plate as an input torque is given to its shaft. The valve-plate shaft can be modeled as shown in Figure 3. (a) Find the transfer function of G(s) = θ(s)/r(s) , then evaluate the stability of thesystem by identifying its poles and zeros. Plot the poles and zeros in an s-plane and characterize the step response damping type. (b) To design a responsive throttle response, the overshoot and settling time need to be set at a certain level. Considering that J and D of our system in Figure 3 can be modified, find the values of J and D to yield 20% overshoot and a settling time of 2 seconds.
Consider ab N-bit DAC whose output varies from 0 to VFS (where the subscript FS denotes "full scale"). (a) Show that a change in the least significant bit (LSB) induces a change of VFS/(2N-1) in the output.This is the resolution of the converter. (b) Convince yourself that the DAC can produce any desired output voltage between 0 and VFS with at most VFS/2(2N-1) error (i.e., one-half the resolution). This is called quantization error of the converter. (c) For VFS = 5 V, how many bits are required tp obtain a resolution of 2 mV or better? What is the actual resolution obtained? What is the resulting quantization error?
Two blocks as open loop and closed loop given in the figurefor the diagram as G1 = 100, G2 = 1000 and H = 0.009are given. a. Find the output voltages when the input voltage is 10 mV. b. Due to the temperature increase for both systems G1 and If G2 is doubled, the input will be 10 mV. What happens to the output voltages even though they remain? c-)You have found results above. About these, the sensitivity of the systemInterpret using the principle.
1. Find the expression of C/CCI in terms of D and R. For a cellular system C/CCI should be minimum 23 dB in a location where path loss exponent is 3.5. Find the value of D/R and K. Also draw the cellular structure of a Cluster of cells where K is the obtained value.
In the case of the circuit shown below:(a) Determinethestateequation?(nextstates D0 and D1) as a function of current states s0 and s1 and input EN).(b) Determinetheoutputequation?(output MAX as a function of current states s0 and s1 and input EN).(c) Given the functions ? and ?, fill in the transition table opposite.
Fill in the blank. 1. The _________ can actually be used as a voltage-controlled resistor because of a unique sensitivity of the drain-to-source impedance to the gate-to-source voltage.2. The ________________ for any JFET is labeled IDSS and occurs when VGS = 0 V.3. The relationship between the drain current and the gate-to-source voltage of a JFET is ______________ as defined by Shockley’s equation. As the current level approaches IDSS , the sensitivity of ID to changes in VGS increases significantly.4. A ______________ device employs a unique combination of a p-channel and an n-channel MOSFET with a single set of external leads.
The output resistance of theMOScurrent source as shown is given by Rout = μf RS. How much voltage must be developed across RS to achieve an output resistance of 5 MΩ at a current of 100 μA if Kn = 500 μA/V2 and λ = 0.02 V−1?
Find the voltage gain expression (?? = ????/???) of the circuit given below in terms of R1, R2, R3, and Rf.
Without writing or drawing tools to lean on, you must use words, not equations, graphs or schematics in your explanation. The current in a differential pair of transistors swings between the two sides of the transistor pair as the input voltage swings between the inputs. The output voltages of course follow the current inversely. Is this swing of current related to one of the chief advantages of differential operation, the elimination of common mode signals? Keep in mind, there is a restricted range of allowed current (and voltage) swing to keep the amplifier operating in a linear way
Q: Find the digital equivalent and the resolution for a 3 bit DAC using Successive Approximation of Vin = 0.4 V and Vref = 1 V?