Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.11 sq.in. Knowing that they support the rigid member BC, determine the downward deflection (in inches) of point E. if x = 17.5 in, y = 23.7 in, z = 21 in, E = 10863545 psi, and P = 46 kips. Round off the final answer to five decimal places. ... D E

Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.11 sq.in. Knowing that they support the rigid member BC, determine the downward deflection (in inches) of point E. if x = 17.5 in, y = 23.7 in, z = 21 in, E = 10863545 psi, and P = 46 kips. Round off the final answer to five decimal places. ... D E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need answer on this asap. thank you! Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.2 sq.in. Knowing that they support the rigid member BC, determine the downward deflection (in inches) of point B. if x = 13.7 in, y = 28.1 in, z = 20 in, E = 10754407 psi, and P = 26 kips. Round off the final answer to five decimal places.
Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.2 sq.in. Knowing that they support the rigid member BC, determine the downward deflection (in inches) of point C. if x = 13.7 in, y = 28.1 in, z = 20 in, E = 10754407 psi, and P = 26 kips.
The rod ABC is made of an aluminum for which E = 71.15 GPa. Knowing that P=10.2 kN and Q=51.62kN, determine the deflection (in um) of point B y=0.46 and z=0.56. Round off the final answer in four decimal places.
Fbd ,formula and calculation should be included. Please work it fast without wasting a time. 1)The rod ABC is made of an aluminum for which E = 70 GPa. Knowing that P = 9 kN and Q = 14 kN, determine the deflection of: (a) Point A, (b) Point B. Consider upward to be positive.
A 4-ft section of aluminum pipe of cross-sectional area 1.75 in2 rests on a fixed support at A. The 58-in.-diameter steel rod BC hangs from a rigid bar that rests on the top of the pipe at B. Knowing that the smodulus of elasticity is 29 3 106 psi for steel and 10.4 3 106 psi for aluminum, determine the deflection of point C when a 15-kip force is applied at C.
The rod ABC is made of an aluminum for which E = 71.4 GPa. Knowing that P = 7.94 kNand Q = 49.88 kN,determine the deflection (in μm) of point B if y = 0.47 and z = 0.54. Round off the final answer in four decimal places.
A 7/8-in.-diameter rod BC is attached to the lever AB and to the fixed support at C. Lever AB has a uniform cross section 38 in. thick and 1 in. deep. For the loading shown, determine the deflection of point A. Use E=29 *106 psi and G=11.2 *106 psi.
A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 × 106 psi, the deflection of point C will be 0.1 in. Determine the diameter of portion BC in inches if P = 50 kips.
Figure 4 shows two solid cylindrical rods and joined at B. The rod ABC is made of an aluminumfor which E = 70 GPa. Knowing that P = 6 kN and Q = 42 kN, determine the deflection of;a) Point Ab) Point B
The length of the 332332 -in.-diameter steel wire CD has been adjusted so that with no load applied, a gap of 116116 in. exists between the end B of the rigid beam ACB and contact point E. Knowing that E = 29 × 106 psi, determine where a 57-lb (w) block should be placed on the beam in order to cause contact between B and E. For contact, x < in.
Both portions of the rod ABC are made of an aluminum for which E = 70.4GPa. Knowing that the magnitude of Q is 31876 N, m = 0.35 m, and n = 0.55 m, determine the value of P (in N) so that the deflection at A is zero.
2.75 The plastic block shown is bonded to a rigid support and to a vertical plate to which a 55-kip load P is applied. Knowing that for the plastic used G = 150 ksi, determine the deflection of the plate.2.76 What load P should be applied to the plate of Prob. 2.75 to produce a 116-in. deflection? Solve 2.76