Water at 20°C is pumped between two large open reservoirs through 1.5 km of smooth pipe. The water surfaces in the tworeservoirs are at the same elevation. When the pump adds 35 kW to the water. the flowrate is 1 m/s. If minor losses arenegligible, determine the pipe diameter.D=m

Answered: Image /qna-images/answer/109de93d-bef2-4b0c-b12d-363aed8318d7.jpg

Answered: ed between two large open reservo ne…

Engineering

Mechanical Engineering

ed between two large open reservo ne elevation When the pump adds

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 5: The pump shown below delivers a head of 50 m to the water through 30 cm diameter with pipe length 500 m. If the head loss is given by determine. L V² 0.02 / 1. The flow rate (Q) through the system in m³/s 2. The input power (Pi) required to supply the pump if the efficiency=75% 2 40 m L w **** AVB
The water in an aquarium will be drained for cleaning. A flexible tube (D = 4mm) will be used to drain the aquarium through siphoning. If the vertical distance between the end of the tube and the water surface is 6Ocm, solve the volumetric flowrate.
A water pump is used to pump the water to a large water tank as shown in Figure. The free surfaces of both water tanks are under atmospheric pressure. Dimensions and local losses are given below. The flow rate of the pump is determined as 16.2 L/min. Calculate the required manometric head of the pump and the required motor power if the total efficiency is 76.2 percent. The water at 10oC. density r = 996.2 kg/m3, dynamic viscosity µ = 1.362x10-3kg /ms. z2-z1 = 7.62 m (height difference), D = 2.62 cm (pipe diameter), L = 176.2 m (total pipe length), ɛ = 0.2562 mm (pipe roughness value) Local loss coefficients: KL,inlet = 0.562 (pipe inlet) KL,valve = 16.2 (valve), KL,elbow = 0.9262 (there are 5 elbows totally in pipe line), KL,outlet = 1.0562 (pipe outlet).
Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are 400 m, 200 m and 250 m and diameters are 300 mm, 200 mm and 250 mm respectively. The difference in water surface in the two tanks is (12+X) m. If coefficient of friction of the three pipes is 0.006, evaluate the following: x=8 (a) Rate of flow through the pipes considering all the losses; (b) Diameter of an equivalent pipe of the same length. H= (12+X) m L;= 400 m L= 200 m Ly= 250 m Jd;= 300 mm d;= 200 mm dy= 250 mm
A pipe line consist of 10 cm diameter for 105 meter and 7.2 cm for the next 68 m. Carries water at the rate of 22 lit/sec. If f 0.005 determine major losses and minor losses. =
Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are 400 m, 200 m and 250 m and diameters are 300 mm, 200 mm and 250 mm respectively. The difference in water surface in the two tanks is (12+X) m. If coefficient of friction of the three Problem 4 pipes is 0.006, evaluate the following: X=7 (a) Rate of flow through the pipes considering all the losses; (b) Diameter of an equivalent pipe of the same length. H= (12+X) m L;= 400 m L2= 200 m d3 300 mm d2= 200 mm L3= 250 m d3= 250 mm Figure 2
At the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to install a pump to circulate a flow of 40(lt/s). The 400m long pipe is cast iron 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 2,9 (kgf/cm²) gauge pressure. Decide the drive power of the pump in KW if its performance is 70%. •Additional data, pressure drop factors: •Retention valve Kᵣ = 1,5 •Gate valve open Kᵥ = 0,21 •Medium Radius Commercial Elbow Kc = 0,75 for each cubit •Storage pond outlet sharp angles Kₛ = 0,5 •Entrance to consumption pond Kₑ = 1 •Friction factor in pipes f = 0.026
Water from a nearby lake is to be used for a fountain and a water tank. The figure below shows the elevations and pipe connections. It is desired that the jet water of the fountain reaches a height of at least 2.5 m from the nozzle outlet. As for the tank, it is elevated in order for it to distribute water using gravity. The specifications of nozzle, suction and discharge pipes are given in the table below. Assuming negligible minor head losses, what is the minimum power input to the pump in kW? Take pump efficiency to be 88% and motor efficiency, 95%. Water from the fountain is returned to the lake through a drainage (not shown in the figure). round off the answer to 4 decimal places
Water flows at the rate of 0.015 m/sec from open reservoir A to open reservoir B (both are large reservoirs that are open to the atmosphere) through two concrete (8 = 0.32 mm) pipes connected in series. If L1 = 800 m, Di = 16 cm, L2 = 200 m, and D2 = 8 cm, determine the difference in water surface elevations (Az) of the reservoirs. The coefficient of contraction (K.) is 0.36, the entrance coefficient is K = 0.5, the exit coefficient is K = 1.0, and assume fully turbulent flow (Xx = 9810 N/m?, Ku = 1.12 x 10-6 m²/s). You do not need to check if the assumption of fully turbulent flow is valid, just assume that it is valid. А Az =? Pipe 1 В Pipe 2 undefined
Reservoir X (Elevation 369m) supplies water to reservoir Y (Elevation 195m) thru a 400 mm pipe. A turbine is installed in the same level with Reservoir Y. The total system flow is 220 gpm determine the the output power in Hp if the turbine is 65% efficient and the total headloss of the system is 4.5m.
Two reservoirs with top surfaces placed on the flat ground and connected with each other with a straight pipe and pump system. The height of the first reservoir is Z1=10 m and the second reservoir is Z2=30 m from the ground level. The pump sucks water from the first reservoir and conveys into the second reservoir. The major head loss along the pipe is hf=40 m with ignoring local head losses. Calculate the manometric head of the pump in a meter of water.
Determine the NPSH available for the system shown. The pump takes water at 30 ° C. The system is installed at sea level. The pump is at 2 m above the water level. The pipe measures 6 m and the diameter of 5 cm. The tubing has a sharp edge entry and the elbow is 90 ° threaded. The flow that the pump moves is 90 liters per minute. The material of the tubing is galvanized iron.