An idelaized centrifugal pump, data given as follows;Blade outer radius of blade = 25 mmPower = 2 KWRunning speed = 2000 rpmEntry of liquid into the pump is axial and exit from the pumpis radial with respect to impeller.Determine the mass fow rate of the liquid through the pump?

Given data; Blade outer radius,r= 25 mm Power,P=2 KW=2000W N=2000 rpmEntry of liquid into the pump…

Answered: Entry of liquid into the pump is axial…

Engineering

Mechanical Engineering

Entry of liquid into the pump is axial and exit from the pump

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: If the gauge pre ssure in a 50-gal tank half-filled with liquid is 100 lbf/in .2, what would be the…

Q: A = rolled steel channel (I 8.87 x 106 mm, I₁ = 40.3 x 10¹ mm²) is used as a simply supported beam…

Q: (d) A round bar shown in Figure 2b is mounted on the end of a motor shaft at its central fixing…

A: given; diameter of rod(d)=0.1mlength(L)=1mspeed(N)=2000rpm

Q: a) What is forced convection? How does it differ from natural convection? Is convection caused by…

Q: As shown below, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends…

Q: 10∙1 A rectangular plate 0.5 m long, 0.25 m wide and 10 mm thick is simply supported at the edges.…

Q: 12. Determine the magnitude of the reaction force at pin support B when 0 = 30°, as shown, to…

A: The magnitude of the reaction force at pin support B: RB = 25.98 kN (Option D)

Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar…

Q: A thermodynamic system with 45 pounds of Neon simultaneously reject heat and receive paddle-work…

Q: Calculate the critical radius of insulation for asbestos (k=0.17 W/m.C) surrounding a pipe and…

A: Thermal conductivity of asbestos, k=0.17 W/m.CRoom air temperature, Ta=17oCHeat transfer…

Q: Q7) Choose the correct answer for the following sentences: a-45° 45' 1- The following vernier bevel…

A: Q.7 A bevel protector Is an instrument that has a graduated circular scale with one pivoted arm…

Q: 2. If the beam cross section is a rectangle with a breadth and depth of 6 in and 8 in respectively,…

Q: 1- An ideal gas mixture whose apparent molar mass is 36 kg/kmol consists of nitrogen N₂ and three…

Q: partition. One compartment contains 3 kmol of N₂ at 600 kPa pressure and the other compartment…

Q: Compute for the moments of inertia and radius of gyration of the shaded area with respect to the x -…

A: Now first of all we need to separate the shapes

Q: A one-hectare vegetable farm uses a shallow tube well (STW) for irrigating the crops on the farm. A…

A: Given data: Power required = 10 hp = 7.457 kW We have to develop a design of an energy system using…

Q: 2. A 20-kg crate hanging at D is supported by a horizontal spring AB and a cable AC, as shown.…

Q: 0.6 kg of a gas mixture of N₂ and O₂ is inside a rigid tank at 2.7 bar, 70°C with an initial…

Q: Task 1 The beam is shown in figure, determine the internal shear force and bending moment in the…

Q: Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

A: When a simply supported beam is subjected to the loading then, at the joints reactions get…

Q: A = - rolled steel channel (Ix 8.87 x 106 mm², I₂ = 40.3 × 10¹ mm²) is used as a simply supported…

A: In a roof truss, we know that a rolled steel channel is employed as a simply supported beam.We must…

Q: A rectangular dam with base equivalent to 2.5-meters and height equivalent to 6-meters holds water…

A: Given: The dam width b = 2.5 m The dam height, h = 6 m The dam thickness, L = 1 m The unit weight of…

Q: 1. If the beam cross section is a rectangle with a breadth and depth of 6 in and 8 in respectively,…

A: Given that, RA+RD=100+80RA+RD=180 ......... 1Taking moment about A,100×2+80×6-RD×9=0RD=75.556…

Q: A 28-in pump is used to deliver water from a lower reservoir to a higher reservoir . The total…

A: Given:d=10 inL=62 ftf=0.022H=365-0.04718Q2

Q: 2. What is oxy-acetylene welding flux? Is there a welding rod coated already with flux? What is the…

A: Oxy acetylene welding is the welding process in which mixture of oxygen and acetylene gas is used…

Q: A model of an aircraft is being tested in a wind-tunnel. If the model was replaced by one that is…

Q: Find the strain Stress-43.5 MPa E=56 MPa

A: Given data : Modulus of elasticity=E Stress=σ To find : Strain

Q: 616. For the beam loaded as shown in Fig. P-616, determine (a) the deflection and slope under the…

A: solution to Problem 617 as mentioned by the student.

Q: A Carnot engine receives heat from source at 327°C causing an increase in entropy is equal to 5…

Q: (1) why the flow faster at the pipe center when you observe few millimeters from the pipe inlet; (2)…

Q: Find potential energy m=2.203 kg g=10 m/s2 h=2.2 m

Q: Which of the following equations below describes the system head of the piping shown below. The…

Q: State the assumptions made in Kinetic theory of gases.

A: The gas laws can be deduced from kinetic theory of gases, therefore the gas equation pv=RT can also…

Q: 6. A railroad track is laid at a temperature of 10°C with gaps of 0.008 m between the ends of the…

A: Given data T1=10°CT2=65°C∆=0.008 mα=11.7×10-6 /°CE=22 GPa Here, T represents the temperature, E is…

Q: A rigid bar AB of length 1.65 m is hinged to a support at A, and supported by two vertical wires…

Q: Determine the mass fow rate of the liquid through the pump?

A: Given data; Running speed,N= 2000 rpm Power,P= 3 kW Blade outer radius of=45 mm Determine mass…

Q: What size of new cast iron pipe (roughness of 0.00026) is needed. to transport 550 L/s of water for…

A: Given data as per the question Q=550 =0.550 m3s Length of pipe =1 km =1000 mhead loss =3m

Q: H.W1 The beam is subjected to the linearly varying distributed load. Determine the maximum…

A: Given Length = L Load, P = w0 Find Deflection

Q: 20. Determine the required force P that must be applied at the blade of the pruning shears so that…

Q: Frid the potential energy

A: Given data : Mass=m Height=h Acceleration due to gravity=g To find : Potential energy

Q: Explain the liquid-vapor equilibrium of pure substances: properties of the two-phase mixture.

A: Given question: Explain the liquid vapor equilibrium of pure substances: properties of two phase…

Q: Find hydraulic radius Wetted area=5 m2 Wetted perimeter-7 m

A: Given data : Wetted area=A Wetted perimeter=P Required : Hydraulic radius

Q: Air with mass of 16 kg is heated at constant gage pressure of 9044 hPa from -24.0 °C to 184 °C.…

Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar…

Q: 15.9 A backward-swept centrifugal fan develops a pressure of 75 mm W.G. It has an impeller diameter…

Q: 9. Determine the moment of the 500 N force about point O, as shown.

Q: Using the relations among load, shear and moment, draw shear and moment diagrams, specifiying the…

A: The section is as shown below,

Q: Crude oil, Cp = 1.9 kJ/(kg.K), flows at a rate of 0.32 kg/s through the inner pipe of a tube-in-tube…

Q: ᴀ ᴘᴇʟᴛᴏɴ ᴡʜᴇᴇʟ ɪꜱ ᴛᴏ ʙᴇ ᴅᴇꜱɪɢɴᴇᴅ ᴛᴏ ʀᴜɴ ᴀᴛ 400ʀᴘᴍ ᴜɴᴅᴇʀ 150ᴍ ᴇꜰꜰᴇᴄᴛɪᴠᴇ ʜᴇᴀᴅ. ᴛʜᴇ ʀᴀᴛɪᴏ ᴏꜰ ᴛʜᴇ ɴᴏᴢᴢʟᴇ…

A: Given pelton wheel turbineN=400rpmH=150mdD=112η=84%=0.84speed ratio=0.55

Q: Problem 5 A tank with square bottom, 45 cm on a side rests on a horizontal surface with coefficient…

Concept explainers

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.

Question

An idelaized centrifugal pump, data given as follows;
Blade outer radius of blade = 25 mm
Power = 2 KW
Running speed = 2000 rpm
Entry of liquid into the pump is axial and exit from the pump
is radial with respect to impeller.
Determine the mass fow rate of the liquid through the pump?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A centrifugal pump with radial inlet (alpha4 = 90°) operates with water at a flow of 0.3 m3 /s. The rotor diameter is 250 mm and the blades it is 30 mm wide at the outlet. Assume that the blades are radial at the exit. Determine the theoretical height considering infinite number of blades and power required when the pump runs at 800 rpm.
A centrifugal pump runs at 1750 rpm while pumping water at a rate of 50L/s. The water enters axially, and leaves tangential to the impeller blades. The impeller exit diameter and width are 150 mm and 10 mm, respectively. If pump requires 45 kW, and its 75% efficient, estimate the exit angle of the impeller blades.
Consider a centrifugal pump with curved blades has blade angle at the outlet section equal to 30o, and no shock/no swirl at inlet. Construct the velocity diagrams of this blade at inlet and outlet sections.
A centrifugal pump outer diameter equal to two times the inner diameter and running at 1200 rpm works against a total head of 75 m the velocity of the flow through the impeller is constant and equal to 3 m/s. The vane are set back at an angle of 30° at outlet. If the outer diameter of the impeller is 600 mm and width at out let is 50 mm, determine; 1- Vane angle at inlet. 2- Work done per second by imepller.
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.
a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
Find the specific speed of a double suction centrifugal pump delivering 1.5 m³/s against a net head of 15 m when running at 725 r.p.m. state the type of impeller to be employed for this pump.
A centrifugal pump running at 3500 rpm pumps water at a rate of 0.01cu. m./sec. The water enters axially, and leaves the impeller at 5m/s relative to the blades, which are radial at the exit. If the pump requires 5kW, and is 67% efficient, estimate the basic dimensions (impeller exit diameter and width).
A test on centrifugal pump operating at 3237 rpm showed a total head of 39 ft at a capacity of 900 gpm. Estimate the total head and capacity of the pump if it were operated at 1750 rpm. Assume normal operation at point of maximum efficiency in each case.
A centrifugal pump discharges 96L/s while running at 1380rpm against a net head of 14m. The manometric efficiency of the pump is 0.92. If the vane angle at the outlet is 35 deg, estimate the outer diameter of the impeller and its width at that diameter. Assume the velocity of flow.
The fluid flow rate was 1 m3 / s and the head was 10 m in the experiment performed at 2000 rev/min by water with the 1/4 ratio model of a centrifugal pump designed to be used for oil. Calculate the power given by the pump to the fluid when the prototype pump operates at 1000 rev/min (ρ water = 1000 kg / m3, ρ oil = 800 kg / m3)
A 2-stage centrifugal pump delivers 50 gpm of 225ºF water against 200 ft head at 3200 rpm. a) What is its specific speed? b) What head could a geometrically similar pump produce if operated at 45 gpm flow?