Electrical Engineering (a) Some polycrystalline photovoltaic cells are to be arranged to provide an output of 12V and a power of 120W. Design and sketch out the cell configuration that meets the specification, using a sketch. The datasheet shows that open-circuit voltage is 0.622V, short-circuit current is 8.XY A, and fill factor is 0.7Z.

Electrical Engineering (a) Some polycrystalline photovoltaic cells are to be arranged to provide an output of 12V and a power of 120W. Design and sketch out the cell configuration that meets the specification, using a sketch. The datasheet shows that open-circuit voltage is 0.622V, short-circuit current is 8.XY A, and fill factor is 0.7Z.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Similar questions

A resistor, an inductor, and a capacitor are connected in parallel to an ac source with voltage amplitude V and angular frequency v. Let the source voltage be given by v = Vcosvt. (a) Show that each of the instantaneous voltages vR, vL, and vC at any instant is equal to v and that i = iR + iL + iC, where i is the current through the source and iR, iL, and iC are the currents through the resistor, inductor, and capacitor, respectively. (b) What are the phases of iR, iL, and iC with respect to v? Use current phasors to represent i, iR, iL, and iC. In a phasor diagram, show the phases of these four currents with respect to v. (c) Use the phasor diagram of part (b) to show that the current amplitude I for the current i through the source is I = √(I2R) + (IC - IL)2 . (d) Show that the result of part (c) can be written as I = V/Z, with 1/Z = √ (1/R2) + [ωC - (1/ωL)]2.
A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?
POWER SİSTEMS high voltage technique it is possible to measure pulsed (AND ANSWER THE SAME QUESTION FOR AC AND DC ) high voltages with the help of two spheres of equal radius placed on the same axis. In which case the approximate impulse,AC AND DC voltage value that can be measured with such a system with diameters of 500 mm and known spacing between them is 2.5 cm, is given correctly. (Ambient conditions are neglected and take Ed = 30 kV / cm2 k = 0.9) a) 68,65114 kV b) 81.30081 kv c) 97,08737 kv d) 65,35947 kv e) 57.48835 kv f) 46.21612 kv PLEASE ANSWER THE SAME QUESTION FOR DC HİGH VOLTAGE AND AC HİGH VOLTAGE WHAT THE DIFFERENCE BETWEEN THEM
Asap Solve and recheck by using another circuit analysis method.
Plz solve this question ASAP Circuits Analysis
Select the forward path gain (M ktop) for the system for the SFG diagram given below
Pls solve this question Circuits Analysis
The terminal points determined by pi/2, pi, -pi/2, 2pi are __________, ________, ___________, and ___________, respectively.
Subject : ELECTRONIC CIRCUIT ANALYSIS AND DEVICES Please give the DC ANALYSIS CIRCUIT and AC EQUIVALENT CIRCUIT of this problem before proceeding to find letter c. (Note : Neglect Vbe)
a) Keeping in mind the Electrical-Mechanical analogy, write down the angular frequency relation (formula) for an ideal LC oscillator. b) If a Resistance R is added in the LC circuit, Energy is dissipated and it becomes a damped RLC oscillator. Considering the fact that the resistor acts as a damping factor, write down the frequency for the damped harmonic oscillator. c) Under what condition are the two frequencies (in a) and b)) equal?
How does the characterization of the circuit as a Thévenin or Norton's equivalent simplify the prediction of the response of a circuit? Consider an AC wall plug. Is it better to model this source as a Thévenin equivalent or as a Norton Equivalent? Explain why. Again consider an AC wall plug. Is this source more like an ideal voltage source or like an ideal current source? Explain why.
A coil of inductance 100 mH and resistance 800 ohm is connected in parallel with a variable The capacitor is across a 12V, 5 kHz supply. Determine for the condition when the supply current is a minimum: (a) the capacitance of the capacitor, (b) the dynamic resistance, (c) the supply current, and (d) the Q-factor