15. The next method to hold work in a lathe that is used for non-cylindrical work parts: Collet Chuck Face plate None of the choices

Q: Turning is a machining process in which a single-point tool removes material from the surface of a…

A: It is true that turning is a machining process in which a single-point cutting tool removes material…

Q: 16-1. blankholder II. chuck III. collet IV. die holder Please name the various way(s) in which a…

A: Lathe machine: It is a device or machine which cane be used to rotate workpiece about an axis of…

Q: Which would you use for any of the following situations: Cutting on a smaller mill, a larger mill…

A: Given data: For cutting a smaller mill  A larger mill with little clearance A smaller diameter…

Q: 4. Explain the differences between the up milling and down milling?

A:

Q: 1. A workpiece with 25mm diameter is turned in a centre lathe with a back rake angle of 12 degrees…

A: For solution refer below images.

Q: In up milling, the chip formed by each cutter tooth starts out very thin and decreases in thickness…

A:

Q: Subject: Machine Shop For pocket operation of 2 x 3-inch surface and depth of 0.06 in using 0.5 in…

A: The importance of cutting speeds and feed is very important and these factors will decide the…

Q: 5. An engine lathe is used to turn a cylindrical work part, cutting speed 2.4 m/s, feed 0.20 mm/rev,…

A:

Q: 3)With neat sketch explain all the operation performed on lathe machine

A: Lathe Machine

Q: Mention the difference between Shaper machine and planer machine?

A:

Q: Q1) Explain the four types of chips formation with sketches? What is tool life in Lathe?

A: 1. CONTINUOUS CHIP- As the name shows these types of chips have a continuous segment and produce…

Q: 8. The most common application for the next operation is to shape metal parts: * Boring Turning All…

A: all options are correct

Q: Name four common methods of holding a workpiece or work part on the lathe machine. Explain also how…

A: Lathe Machine : A lathe is a machine in which rotates a workpiece about an axis of rotation to…

Q: Identify the machining operation

A:

Q: What products can be produced from turning process in lathe machine. (other than spur gears or…

A:

Q: In an orthogonal machining with a tool of 9 orthogonal rake angle, the uncut chip thickness is 0.2…

A: Given:Orthogonal rake angle, α=9ouncut chip thickness, t=0.2 mmmaximum chip thickness, tmax=0.4…

Q: Why should the overhang distance of a lathe tool be minimized? What occurs if a lathe tool is set…

A:

Q: The type of milling operation to produce flat surfaces with the cutter axis parallel to the milled…

A:

Q: What variable factors to be consider before operating any lathe operations? How you can set these…

A: What Is Lathe ? A machine for shaping wood, metal, or other material by means of a rotating drive…

Q: how would you make the champhers on a lathe?

A: Chamfer refer to the slope  cut at any right edge of a work piece for example holes, ends of the…

Q: How do you center a workpiece in a lathe machine with a four-jaw independent chuck?

A: Concept: 1) Generally this four jaw independent chuck is used to workpiece of different shape like…

Q: machining time per pass is minutes.

A: Given data; block length(l)= 200 mmmilling cutter diameter (D)=34mmdepth of cut=2mmtable…

Q: QUESTION 1 Calculate the spindle speed in RPM of a lathe turning a 96 milimeter diameter material…

A: Given:d=96 mmV=148 SMPM

Q: Name the various ways in which a work-part can be held in a lathe.

A: given: Name the various ways in which a work-part can be held in a lathe.

Q: Differentiate a lathe machine into a shaper machine in terms of operating principle

A:

Q: Q3. Identify the secondary machining process from the following.

A:

Q: In a single pass turning operation t speed is the only variable based on time cost and the cutting…

A: Given:cost of 1 cutting edge,C=5 Rsmachine tool cost,L=75 Rs/hr =7560=1.25VT0.1=100

Q: In lathe machine, the movement of the tool parallel to the axis of the job is known…

A: Basics of Lathe machine.

Q: Q1 The tool signature of a single point cutting tool in NRS system is 15° – 10° – 5° – 10° – 25° –…

A:

Q: Make a steps on how to center the cutting tool with the lathe center line.

A: A high-speed steel cutting tool is used to perform the operation of step turning operation in a…

Q: 11. In the following operation the axis of the tool is perpendicular to feed direction: * Slotting…

A: peripheral milling = tool axis is parallel to the feed direction 1) slotting  2) slab milling

Q: Name the different types of chucks used in lathe machine?

A: Chucks are used to hold the object which has to be machined,

Q: Type of milling operation to produce flat surfaces with cutter axis perpendicular to the milled…

A: according to the given details in the question.

Q: In a multi point cutting tool the positive rake angle is used to cut low tensile strength and…

A: This question is from manufacturing engineering subject.

Q: Sketch and explain up milling operation

A: We have to explain up milling

Q: Identify the machining operation Work Face Milling Slotting

A: Answer:-  Straddle milling operation.

Q: In what units are feed rates measured for lathe operations?

A: Feed rate is the measurement of the spindle's travel distance per rotation. The feed rate is…

Q: QUESTION 12 How long would it take a turn 6 inches of 1-inch bar stock on a No. 3W. and S. turret…

A: This is the very basic question of machining time calculation on lathe.

Q: 8. Turning is a machining process in which a single-point tool removes material from the surface of…

A: The general process of turning involves rotating a part while a single-point cutting tool is moved…

Q: 4)Write down the different specification of lathe machine

A: Lathe Machine

Q: 4. Differentiate a lathe machine into a shaper machine in terms of operating principle

A: GIVEN DATA - LATHE AND SHAPER MACHINE GIVEN WE HAVE TO DIFFERENTIATE IN TERMS OF OPERATION

Q: Identify the part of a lathe machine which is used to give longitudinal feed motion for the tool.…

A: option  ( B )   carriage

Q: 21.16 (b): (USCS units) The slab milling that was performed on the top surface of a rectangular…

A:

Q: What is the difference between extruded boss/base and extruded cut, revolved boss/base and revolved…

A: To write: The difference between extruded boss/base and extruded cut,  revolved boss/base and…

Q: Identify the Lathe operation, performed without the tool moving parallel to the axis of the job is…

A: Different lathe operations are turning, facing, grooving, parting, threading, drilling, boring,…

Q: st common machining processes.

A: given: Name the three most common machining processes.