Turning is a machining process in which a single-point tool removes material from the surface of a rotating cylindrical workpiece, the tool being fed in a direction parallel to the axis of work rotation The difference between a live center and a dead center used in the context of work holding in a lathe. A center holds the work during rotation at the tailstock end of the lathe. A live center is mounted in bearings and rotates with the work, while a dead center does not rotate - the work rotates about it. mounted in bearings and rotates with the work, while a dead center does not rotate - the work rotates about it(a) true or (b) false

Turning is a machining process in which a single-point tool removes material from the surface of a rotating cylindrical workpiece, the tool being fed in a direction parallel to the axis of work rotation The difference between a live center and a dead center used in the context of work holding in a lathe. A center holds the work during rotation at the tailstock end of the lathe. A live center is mounted in bearings and rotates with the work, while a dead center does not rotate - the work rotates about it. mounted in bearings and rotates with the work, while a dead center does not rotate - the work rotates about it(a) true or (b) false

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter6: Milling

Section6.4: Indexing And Rotary Table Operations

Problem 6RQ: If the outside of a 6"-diameter disk is to be milled using a rotary table and a 3/4" diameter...

See similar textbooks

Similar questions

8 A job has to be machined in shaping and the process parameters are given below: a. Length of the job=120 mm b. Speed of the motor=640 rpm c. Cutting speed=264 m/min d. Tool allowance before cutting =30 mm e. Tool allowance after cutting=15mm Determine the cutting to return stroke ratio for the above operation and draw the arrangement of machining with tool head and allowances.
Find the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.
ME 408 - Machine Shop Theory and Practice How do you center a workpiece in a lathe machine with a four-jaw independent chuck?
In a turning operation, the operator has established that a single pass on the cylindrical workpiece must be completed in 5.0 min. The piece is 400 mm long and 150 mm in diameter. Using a feed of 0.30 mm / rev and a depth of cut of 4.0 mm, what speed of cut should be used to meet this machining time?
In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to the center of the workpiece, the spindle speed (n) is needed to be: a/Increased b/Decreased c/Maintained the same
A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…
In an orthogonal machining with a tool of 9 degree orthogonal rake angle, the uncut chip thickness is 0.2mm. The chip thickness fluctuates between 0.25 mm and 0.4 mm. The ratio of the maximum shear angle to the minimum shear angle during machining is
Suppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.
For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
(j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min, feed = 0.3 mm/rev, and depth of cut = 8 mm. How much power will the lathe draw in performing this operation if its mechanical efficiency = 95%. Use Table below to obtain the appropriate specific energy value.
Suppose you have a turning operation using a tool with a zero back rake and 5° end relief. The insert flank has a wear land on it of 0.020 in. How much has the diameter of the workpiece grown (increased) due to this flank wear, assuming the tool has not been reset to compensate for the flank wear?