(Electrochemical Machining) An ECM operation is used to cut a hole into a plate of stainless steel that is 10 mm thick. The hole has a rectangular cross section, 15 mm by 25 mm. The operation is accomplished at a current = 1300 amps. Efficiency is 97%. Determine the feed rate and time to cut through the plate. The specific removal rate C for stainless steel = 2.46 x 10-2 mm3/A-s. R - V = CIt I = V = gr A V At fr EA gr C(EAt) gr fr = CI A CE gr Typical values of specific removal rate C' for selected work materials in electrochemical machining. Compiled from data in [11]. Specific Removal Rate C Materialª mm³/amp-sec (in³/amp-min) Materialª Aluminum (3) Copper (1) Iron (2) Nickel (2) 3.44 x 10-2 7.35 × 10-2 3.69 × 10-2 (1.26 × 10-4) (2.69 x 10-4) (1.35 × 10-4) 3.42 × 10-2 (1.25 × 10-4) X Low alloy steel High alloy steel Stainless steel Titanium (4) Specific Removal Rate C mm³/amp-sec (in³/amp-min) (1.1 × 10-4) 3.0 x 10-2 2.73 × 10-2 2.46 × 10-2 (1.0 × 10-4) (0.9 × 10-4) 2.73 × 10-2 (1.0 × 10¯4) a The most common valence given in parentheses () is assumed in determining specific removal rate C. For a different valence, multiply C by the most common valence and divide by the actual valence.

(Electrochemical Machining) An ECM operation is used to cut a hole into a plate of stainless steel that is 10 mm thick. The hole has a rectangular cross section, 15 mm by 25 mm. The operation is accomplished at a current = 1300 amps. Efficiency is 97%. Determine the feed rate and time to cut through the plate. The specific removal rate C for stainless steel = 2.46 x 10-2 mm3/A-s. R - V = CIt I = V = gr A V At fr EA gr C(EAt) gr fr = CI A CE gr Typical values of specific removal rate C' for selected work materials in electrochemical machining. Compiled from data in [11]. Specific Removal Rate C Materialª mm³/amp-sec (in³/amp-min) Materialª Aluminum (3) Copper (1) Iron (2) Nickel (2) 3.44 x 10-2 7.35 × 10-2 3.69 × 10-2 (1.26 × 10-4) (2.69 x 10-4) (1.35 × 10-4) 3.42 × 10-2 (1.25 × 10-4) X Low alloy steel High alloy steel Stainless steel Titanium (4) Specific Removal Rate C mm³/amp-sec (in³/amp-min) (1.1 × 10-4) 3.0 x 10-2 2.73 × 10-2 2.46 × 10-2 (1.0 × 10-4) (0.9 × 10-4) 2.73 × 10-2 (1.0 × 10¯4) a The most common valence given in parentheses () is assumed in determining specific removal rate C. For a different valence, multiply C by the most common valence and divide by the actual valence.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
In Electric Discharge Machining (EDM) for Die Sinking operation which has the following characteristic: Vo = 240 V, R = 10 Ω and C = 2 µF. To perform at maximum removal rate (MRR), calculate the discharge voltage and the charging time (tc).
Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square hole in a copper plate of 18 mm thickness. The dimensions of the hole is 20 mm on each side, however, the electrode dimension shall be slightly less than 20 mm to allow for overcut, and its shape includes a hole in its center to permit the flow of electrolyte and reduce the area of cut. The frontal area of electrode is 180 mm2. The specific removal rate for copper is C = 7.35 x 10-2 mm3/A-s. The applied current is 950 A. At 90 % efficiency, determine the time required to cut a hole of required dimensions.
2 2 .4 1 Emulsion cutting fluids typically consist of 95% water and 5% soluble oil and chemical additives. W hy is the ratio so unbalanced? Is the oil needed at all?
In an orthogonal cutting test with a bar of 75 mm diameter is reduced to 73 mm by using a HSS tool with arake angle  = 10o, following observations were made: length of the chip, lc = 69.44 mm, cutting ratio r =0.3, the horizontal component of the cutting force, FH = 1450 N, and the vertical component of the cuttingforce, FV = 850 N. The various parameters recorded in this cutting operation are: depth of cut, d = 2 mm;feed rate, f = 0.3 mm/rev, cutting speed, V = 60 m/min. Using Merchant’s theory calculate the following:1) Friction force along rake face2) Normal force acting on rake face3) Shear force along the shear plane4) Normal force acting on shear plane5) The percentage error in shear angle predicted by Merchant’s theory6) Shear velocity7) Chip velocity8) Total work done9) The shear work proportion out of the total work done10) The friction work proportion out of the total work done
42 Explain the function(s) of electrolyte in Electro-chemical Machining process.
(b) Explain the function(s) of electrolyte in Electro-chemical Machining process.
nontraditional machining methods (NTM) 1. What industries have benefitted from the development of NTM operations?
What is CNC Machining? Definition, Processes and Components.
Please solve question 2,3 and 13. Determine the % change in the machine time for an USM operation cutting WC plate when the tool material is changed from copper to stainless steel. Take ratio of flow stress of WC to flow stress of copper is 4.6 and the ratio of flow stress of WC to the flow stress of SST is 1.2.
Outline wire electric discharge machining, its physics and applications?
A part to be turned in an engine lathe must have asurface finish of 1.6 mm. The part is made of a freemachining aluminum alloy. Cutting speed = 150 m/min,and depth of cut = 4.0 mm. The nose radius on the tool =0.75 mm. Determine the feed that will achieve thespecified surface finish.