Elements of the lower arm areshown in the figure. The weight ofthe forcarm is 5 Ib with mass centerat G if the T= 0 N. Determine thecombined moment about the elbowpivot (o) of the weights of the forearm and the sphere, from thefollowing answers which of them is5 Ib8 lb13correct:M= 128.6 Ib.inM= 134 Ib.inM= 107.441 Ib.inM=0 Ib.inM=144 Ib.in Determine the weight in newton's of awoman whose weight in pounds is 130, fromthe following answers which of them iscorrect:587 N687 N578 N1274 N

Elements of the lower arm are shown in the figure. The weight of the forearm is 5 Ib with mass center at G if the T= 0 N. Determine the combined moment about the elbow pivot (o) of the weights of the fore arm and the sphere, from the following answers which of them is 5 Ib 13 correct: O M= 128.6 Ib.in M= 134 Ib.in M= 107.441 Ib.in M=0 Ib.in M=144 Ib.in

Elements of the lower arm are shown in the figure. The weight of the forearm is 5 Ib with mass center at G if the T= 0 N. Determine the combined moment about the elbow pivot (o) of the weights of the fore arm and the sphere, from the following answers which of them is 5 Ib 13 correct: O M= 128.6 Ib.in M= 134 Ib.in M= 107.441 Ib.in M=0 Ib.in M=144 Ib.in

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.89RP: The woman is trying to move the crate of weight W by pulling on the rope at the angle to the...

See similar textbooks

Similar questions

The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B, the sag in the cable is 5 m. Find the span L of the cable.
A demonstration gyroscope wheel is constructed by removingthe tire from a bicycle wheel 0.650 m in diameter, wrapping leadwire around the rim, and taping it in place. The shaft projects 0.200 mat each side of the wheel, and a woman holds the ends of the shaft inher hands. The mass of the system is 8.00 kg; its entire mass may be assumedto be located at its rim. The shaft is horizontal, and the wheel isspinning about the shaft at 5.00 rev/s. Find the magnitude and directionof the force each hand exerts on the shaft (a) when the shaft is at rest;(b) when the shaft is rotating in a horizontal plane about its center at0.050 rev/s; (c) when the shaft is rotating in a horizontal plane about itscenter at 0.300 rev/s. (d) At what rate must the shaft rotate in order thatit may be supported at one end only?
Determine the moment MAB produced by the force F shown in the figure which tends to rotate the bar about the axis AB.
The pumping unit is used to recover oil. When the walking beam ABC is horizontal, the forceacting in the wireline at the well head is 250 lb. Determine the torque M which must beexerted by the motor in order to overcome this load. The horse-head C weighs 60 lb andhas a center of gravity at Gc. The walking beam ABC has a weight of 130 lb and a centerof gravity at GB, and the counterweight has a weight of 200 lb and a center of gravity atGW. The pitman, AD, is pin connected at its ends and has negligible weight.
Use the Section Method to find member forces EA, BE, and CB. P = 4 kN
The jib crane is fixed at (A) and carry a box of ( 2500 kg ) mass, as shown in the figure. Determine the reactions on the jib crane at point ( A ). 60 5 m 7 m
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
The young tree, originally bent, has been brought into the vertical position by adjusting the three guy-wire tensions to AB = 3 lb, AC = 9 lb, and AD = 11 lb. Determine the force and moment reactions at the trunk base point O. Neglect the weight of the tree.
Find the torque T, in Nm, that will keep the mechanism balanced at q = 30 degrees in the system shown. The limbs AE and CD are connected to each other at their midpoints, each having a length of L = 3.7 meters and a mass of m = 117 kg. The mass of the upper horizontal platform-shaped limb is 248 kg and the mass of the car is 1.123 kg and they have the centers of gravity shown in the figure.
Crane boom of mass 450 kg with its center of mass at C isstabilized by two cables AQ and BQ. The crane boom lies in the y–zplane. Find the forces in each cable (P=20 kN)
The 4.00 m boom is uniform and weighs 2550 N. Find the tension in the guy wire and the force exerted on the boom at its lower end.
If the 15 kg bar has a center of mass at G, calculate the resulting moment at point O.