0.60 m lighest water level Lowest water level 21.0 m 1.5 m 672.00 m E Dacil + Water will be withdrawn from a river at a flowrate of Q = 3790 L/min for a nearby community. %3D a) Calculate the diameters of backwash and suction pipes assuming Vsuction = 1.5 m/s and Vbackwash=3 m/s. b) Find the diameter of the cylindrical strainer if the velocity through its holes will be kept at 0.15 m/s. (cylinder height can be taken as 0.6)

0.60 m lighest water level Lowest water level 21.0 m 1.5 m 672.00 m E Dacil + Water will be withdrawn from a river at a flowrate of Q = 3790 L/min for a nearby community. %3D a) Calculate the diameters of backwash and suction pipes assuming Vsuction = 1.5 m/s and Vbackwash=3 m/s. b) Find the diameter of the cylindrical strainer if the velocity through its holes will be kept at 0.15 m/s. (cylinder height can be taken as 0.6)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
A Francis radial-flow hydroturbine is being designed with the following dimensions: r2 = 2.00 m, r1 = 1.42 m, b2 = 0.731 m, and b1 = 2.20 m. The runner rotates at n. = 180 rpm. The wicket gates turn the flow by angle ?2 = 30° from radial at the runner inlet, and the flow at the runner outlet is at angle ?1 = 10° from radial. The volume flow rate at design conditions is 340 m3 /s, and the gross head provided by the dam is Hgross = 90.0 m. For the preliminary design, irreversible losses are neglected. Calculate the turbine specific speed of the turbine. Provide answers in both dimensionless form and in customary U.S. units. Is it in the normal range for a Francis turbine? If not, what type of turbine would be more appropriate?
A Francis radial-flow hydroturbine is being designed with the following dimensions: r2 = 2.00 m, r1 = 1.42 m, b2 = 0.731 m, and b1 = 2.20 m. The runner rotates at n. = 180 rpm. The wicket gates turn the flow by angle ?2 = 30° from radial at the runner inlet, and the flow at the runner outlet is at angle ?1 = 10° from radial. The volume flow rate at design conditions is 340 m3 /s, and the gross head provided by the dam is Hgross = 90.0 m. For the preliminary design, irreversible losses are neglected. Calculate the inlet and outlet runner blade angles ?2 and ?1, respectively, and predict the power output (MW) and required net head (m). Is the design feasible?
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
For the water channel fl ow of Fig.=, h 1 = 0.45 ft,H = 2.2 ft, and V 1 = 16 ft/s. Neglecting losses and assuminguniform fl ow at sections 1 and 2, fi nd the downstreamdepth h 2 ; show that two realistic solutions are possible.
Water flows naturally from a tank A located at 20 m above the ground level , to a ground leveltank B . The connecting pipeline between tank A and tank B has an equialent loss coefficient of K .Determine the flow rate Q= ? ( USE g= 10 m 2/s) Note that K0,5 : square root of K. ANSWER: 20 / K0,5 m3/s
A hydroelectric power generating system is shown in the figure. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 286 liters per second. The total length of pipe connecting the two reservoirs is 186 m. The pipe diameter is 346 mm and the Hazen-Williams coefficient is 129. The water surface elevations of reservoirs 1 and 2 are 194 m and 69 m, respectively. Determine the power in kW required by the turbine if it is 63% efficient? Neglect minor losses. Round your answer to 3 decimal places.
Q5: What is the diameter of smalle pipe, if the flow rate (30 lit/sec) ? ·S=0.6 D= Ans: 146.8 mm² 40cm D = 200mm D=?
The following data were obtained for the flow of 20°C water at20 m3/h through a badly corroded 5-cm-diameter pipe thatslopes downward at an angle of 8°: p1 = 420 kPa, z1 = 12 m,p2 = 250 kPa, z2 = 3 m. Estimate (a) the roughness ratio ofthe pipe and (b) the percentage change in a head loss if thepipe were smooth and the flow rate the same.
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. the total length and diameter of the sunction and discharge pipe are 500 mm,1500 m and 300 mm, 1000 m respectively. assumme a head lose of 2 meters per 100 m length of the sunction pipe and 3m per 100 m length of the discharge pipe. what is the required horsepower of the pump?
choose the correct answer Q1A- Using water jet forces to operate turbines in hydropower plant consider application of: * a) Bernoulli’s equation b) Darcy-Weisbach Equation c) Manning equation d) Momentum equation E-none of all above B-The main difference between the flow in pipes and the flow in open channels is * a) Existing the head loss b) Existing the free surface c) Existing the pressure drop d) None of all above