In the figure shown below there are 125 ft of 2-in pipe, 75 ft of 6-in pipe, and 150 ft of 3-in pipe, all cast iron. There are two 90° elbows and an open globe valve, all flanged. If the exit elevation is zero and the elevation at A is 100 ft, what horsepower is extracted by the turbine when the flow rate is 0.16 ft3/s of water at 20 °C? For water at 20 °C, take p = 1.937 slug/ft3 and u = 2.09E-5 slug/ft-s. For cast iron, ɛ = 0.00085 ft. For Re = 113500, 37800, and 75600, take f 0.0314, 0.0266, and 0.0287 respectively. A 2 in Орen globe Turbine 6 in 3 in

In the figure shown below there are 125 ft of 2-in pipe, 75 ft of 6-in pipe, and 150 ft of 3-in pipe, all cast iron. There are two 90° elbows and an open globe valve, all flanged. If the exit elevation is zero and the elevation at A is 100 ft, what horsepower is extracted by the turbine when the flow rate is 0.16 ft3/s of water at 20 °C? For water at 20 °C, take p = 1.937 slug/ft3 and u = 2.09E-5 slug/ft-s. For cast iron, ɛ = 0.00085 ft. For Re = 113500, 37800, and 75600, take f 0.0314, 0.0266, and 0.0287 respectively. A 2 in Орen globe Turbine 6 in 3 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 95 m below the reservoir surface. The turbine delivers 0.950 MW. Calculate the required flow of water in m3/min if friction is neglected. If friction were included would a higher or lower flow rate be required? (Note: The equation you will solve in this problem has multiple roots. Find a solution less than 1.0 m3/s.) V=___m^3/min?
A 6 in. pipe, as shown in the figure, takes water from a reservoir and terminates in a nozzle having a jet diameter of 2 in. Assuming a nozzle loss of 8 percent of the velocity head in the jet, compute the discharge (in S.I. units). Also, make a table showing the elevation head, velocity head, pressure head, and total head at each of the six stations. Lastly, draw the hydraulic gradient line (H.G.L.) & the energy gradient line (E.G.L.).
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe, the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B.
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
In the system of reservoirs shown below, the flow of Reservoir 1 to Reservoir 2 is Q=15 cfs. At point 1 (just before the valve) and point 2 (just before the pipe bend), the total energy head (E) is given as shown. Additionally, the elevation of Reservoir 2 is given as 230 ft. Minor head losses can be accounted for with the following assumptions: angle=120° Radius of curvature of pipe bend at Point 2 is 12ft. (smooth 90 degree bend) Valve is a fully open gate valve Find the following: The height of Reservoir #1 (HR1)
Water (@75C) flows horizontally in a pipe at a rate of 1.6 m3 / min . The dia of the outlet is 2 inches. It enters a 3 inches 45 deg. elbow and is diverted upwards into a connecting pipe. If the pressure just before the elbow is 78 kPa, calculate the magnitude and direction of the force necessary to keep the elbow in place. Say, frictional losses in the elbow are negligible.
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
The turbine of a micro-hydroelectric power plant delivers 65hp at 75% efficiency. If the effective head is 115ft, how many cubic feet per minute of water must be used.
A vertical pipe in the form of a cone has a diameter of 45 cm at the top and 92 cm at the bottom and is 18.3 m long. The head loss is 3 m in either direction when the velocity at the top is 9.15 m/s and the pressure head there is 1.98 m of water. Find the pressure head at the bottom when the flow is (a) downward (b) upward. Draw the diagram.
In a certain hydraulic turbomachine, the following data apply:Inlet blade velocity is 20 m/s. Vu1=21 m/s; Vr1=10 m/s.At the exit, V2 is purely axial and has a value of 14 m/s, and blade speed is9 m/s. Is this power absorbing or power producing? Find E and the changes instatic and stagnation pressures. Would this machine be classified as a purelyradial, purely axial, or mixed flow type?Ans: E=420 J/kg; Δpstag=420 kPa; Δpstat=247.4 kPa