EX: A system consisting of a stone of mass 10 (kg) and a container containing water. The stone was initially 2 (m) above the surface of the water, and that the stone and the water were at the same temperature. After that the stone fell into the water. Calculate the change in internal energy, kinetic energy, potential energy, as well as the heat and work received for the following cases.

EX: A system consisting of a stone of mass 10 (kg) and a container containing water. The stone was initially 2 (m) above the surface of the water, and that the stone and the water were at the same temperature. After that the stone fell into the water. Calculate the change in internal energy, kinetic energy, potential energy, as well as the heat and work received for the following cases.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.37P

See similar textbooks

Similar questions

The two ways that fresh air enters a structure are _______and_____.
Nitrogen with a mass of 1.5 kg expands at a constant pressure. The initial pressure and temperature in the piston cylinder assembly is 170 kPa and 27 deg. C, respectively. Due to heat transfer, the system reached a final temperature of 200 deg. C. Calculate the total change in internal energy.
There is 10-kg of water at room temperature and pressure in a closed piston-cylinder. Boundary work is then done on the system, compressing it until the volume decreases to one-half of it's original value. If the internal energy of the system decreases by 700 kJ/kg during this process and 200 kJ/kg of boundary work is done on the system, how much heat has been removed from the system, in kJ. Assume that system is sitting on a lab bench.How much heat is removed from the system, in kJ?
In a piston-cylinder assembly, there is initially 2 kg of water at a temperature of 25 °C and a pressure of 100 kPa. Then heat is given to the water until its volume is 0.4 m3. At this point, the piston in the cylinder is fixed with a stopper, but the water in the cylinder continues to heat until its temperature reaches 300 oC. According to this, calculate a) the final pressure of the water, b) the amount of heat given to the water, c) the work done by the piston. d) Show these processes in the T-v (Temperature-Specific Volume) diagram
The figure below shows a turbine-driven pump that provides water to a mixing chamber located dz⁢= 5 m higher than the pump, where m˙=50 kg/s. Steady-state operating data for the turbine and pump are labeled on the figure. Heat transfer from the water to its surroundings occurs at a rate of 2 kW. For the turbine, heat transfer with the surroundings and potential energy effects are negligible. Kinetic energy effects at all numbered states can be ignored. Determine:(a) the magnitude of the pump power, in kW.(b) the mass flow rate of steam, in kg/s, that flows through the turbine.
In the 1970s cartoon The Super Friends, the Wonder Twins helped Superman and others fight crime. One of the Wonder Twins was Zan, who was able to take on the form of H2O in its various phases (ice, liquid water, water vapor). After taking a physics class, he decides to conduct a little experiment by turning into an ice igloo in the park on a hot day. (a) If his total mass as an igloo is 64.50 kg and he starts with a temperature of −13.50°C, how much heat must flow into him to completely melt his body? J(b) He continues absorbing energy up to the point where he would start to vaporize (100.0°C). How much more heat is required to raise his temperature to the vaporization point? J(c) How much more heat is required to turn him into water vapor at 100.0°C? J(d) If we model the water vapor molecules making up his body as having only six degrees of freedom, what is the average kinetic energy of one of the water vapor molecules that make up Zan? (Consider the case when Zan is water vapor at…
A man is standing on a board on a frozen lake where there is no friction between the board and the ice surface. Tha man's mass is 2 m and the boaf's mass is 4 m. The board has length L. He walks from 1/5 Lfrom the left end of the board to 1/5 L from the right end of the board. How far and in which direction does the board move during this process?
A piston-cylinder arrangement contains water at 112°C, 84% quality with a volume of 0.98 L. What is the initial mass, in grams? The system is then heated, causing the 150-mm-diameter piston to rise and encounter a linear spring with k = 800 kN/m. Calculate the specific internal energy (kJ/kg) at this instant knowing that the measured volume is 1.65 L. The heating continues and compresses the spring in the process. When the piston encounters the stops, the pressure is 200 kPa. What is the temperature (in °C) and entropy (in J/K) at this point? Heating then continues until the pressure reaches 300 kPa. What is the volume, in L, at this instant? Illustrate the complete process in separate P-v and T-v diagrams.
Volume 0.05 m3 while the piston is attached with the pinin a cylinder with 200 kPa pressure and 300 Kthe temperature is. As a result of heat transfer from the environment, the pressure is 0.4 MPa, the pin breaks, and when the system becomes thermodynamically balanced, its volume is 0.1 m3. Area of piston 0.05 m2, piston and masses on 150 kg and atmospheric pressure102 is KPA. a)Find the temperature at the moment the pin breaks. b)Calculate the pressure and temperature after the pin breaks and reaches the equilibrium position.
The volume of air delivered by fan is 12 m^3/sec and 59 mm water gage. The density of air is 1.9 kg/m^3 and the motor power needed to drive the fan is 50 kW. Determine the fan efficiency in % Answer in whole number
(i) A can of soft drink at room temperature is put into the refrigerator so that it will cool. Would you model the can of soft drink as a closed system or as an open system? (ii) A candle is burning in a well-insulated room. Taking the room (the air plus the candle) as the system, determine if there is any heat transfer during the burning process. Explain how?
A 8 kgs gas contained in a vertical piston cylinder assembly is shown in the figure below. The area and the mass of the piston are 300 cm2 and 15 kg, respectively. A spring is loaded in the piston, which the force exerted varies linearly with the displacement, s. At initial position, the piston face is at s=0, the spring exerts no force. Heat is added to the air causing the gas to expand until the piston reached the stops at s=0.08m and the heat transfer ceases. The atmospheric pressure is 1 bar, the observed gravitational acceleration is g=9.81 m/s2, consider the spring constant, k to be 8,500 N/m and neglect friction between the piston and the cylinder. Determine: a.The initial pressure of the gas in Kpa b.The work done by the gas on the piston in J c.The heat transfer in J, when the specific internal energies of the gas at the initial and final states are energies of the gas at the initial and final states are 210 KJ/Kg and 335 KJ/Kg, respectively