Q2: Find the cooling load of a barber shop due to infiltration and ventilation. The inside conditions are 24 °C and 50% RH, while the outside conditions are 48 °C and 30% RH. The shop has a designed occupancy of 4 barbers and maximum 10 customers. Consider the infiltration rate through the building is equal to 0.35. The shop dimensions are (L= 7, W= 5, H= 3.5) m.

Q2: Find the cooling load of a barber shop due to infiltration and ventilation. The inside conditions are 24 °C and 50% RH, while the outside conditions are 48 °C and 30% RH. The shop has a designed occupancy of 4 barbers and maximum 10 customers. Consider the infiltration rate through the building is equal to 0.35. The shop dimensions are (L= 7, W= 5, H= 3.5) m.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

The suction condition of an air compressor is 104 kPa, 28 deg.C, and 6.81 m^3/s. If the surrounding air is 135 kPa, 32 deg. C Determine the free air capacity in m^3/sec. Answer in whole number
A ventilation system includes a fan with a mechanical efficiency of 45% against a static pressure of 30cm WG. If the total pressure created by fan is 300m of air, what is the static efficiency?
1. Water in the rural areas is often extracted from underground water source whose free surface is 60 m below ground level. The water is to be raised 5 m above the ground by a pump. The diameter of the pipe is 10 cm at the inlet and 15 cm at the exit. Neglecting any heat interaction with the surroundings and fictional heating effects. What is the necessary power input to the pump in kW for a steady flow of water at the rate of 15 li/s? Assume pump efficiency of 74%.
An office to be air conditioned for 50 staff when the outdoor conditions are 30°cDBT and 75% RH if the quantity of air supplied is 0.4m3/min/per find i) Capacity of cooling coil ii) capacity of heating coil iii) amount of water vapourremoved per hour. Assume that required air inlet conditions are 20°c DBT and 60% RH air is conditioned first by cooling and dehumidifying and by heating. Ifthe heating coil surface temperature is 25°c, find the bye pass factor of the heating coil.
air is compressed polytropically in a cylinder according to PV=C. the work required is 180 kj/kg. determine the Heat transferred
Solve the problem. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 lb/cu ft and discharges it with a density of 0.304 lb/cu ft. At the suction, pressure is 15 psia, at discharge pressure is 80 psia. The increase in the specific internal energy is 33.8 Btu/lb and the heat transferred from the air by cooling is 13 Btu/lb. Determine the work on the air in Btu/min and in hp. Neglect change in kinetic energy.
A gas cylinder with interior volume 11.6 L holds compressed air at 17.4 MPa. The cylinder is joined by a hose of negligible volume to a second cylinder that’s been pumped down to vacuum. When the valve on the full cylinder is opened, the air expands to fill the entire system, all the while maintaining a constant temperature. If the energy that becomes unavailable to do work is 171.8 kJ, what’s the volume of the second cylinder (L)?
A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific volume is 12.6 ft3/lb and the final specific volume is 3.25 ft3/lb. If the inlet suction line is 4 in. ID and the discharge line is 2.5 in. ID, determine (a) the change in flow work between the boundaries, ft-lb/min; (b) the mass rate of flow, lb/min; and (c) the change in velocity. Answer: (a) 324,000, (b) 15.88, (c) -12.9 fps
Helium is used in the Carnot engine where the volumes beginning withconstant temperature heat addition are V 1 = 0.3565 m^3 ; V 2 = 0.5130 m^3 ; V 3 = 8.0m^3 ; V 4 = 5.57 m^3 . Determine the thermal efficiency. Use 1.66 as the specificratio of helium. show diagram
Air passes through an insulated nozzle from an initial velocity of 15 m/s to a final velocity of 300 m/s. Assuming air to be an ideal gas, what is the temperature drop of air with Cp = (7/2)R?
one pound of air with an initial temperature pf 200F is allowed to expand without flow between pressure of 90 and 15 psia. If the air is undergoing a process that follows pVn=c, where n= 1, what is heat transferred in Btu?
A steam power plant is located in the northern part of the country. Steam in the plant flows steadily through a 0.17-m diameter pipeline from the steam generating unit (SGU) to the steam turbine. At the SGU end, the steam conditions are determined to be P = 4 MPa, t = 400°C, h = 3,247 kJ/kg, and specific volume = 0.181 m³/kg. At the steam turbine end, the conditions are found to be P = 3.5 MPa, t = 392°C, h = 3,178.3 kJ kg, and specific volume = 0.248 m³/kg. Heat loss from the pipeline is 7.86 kJ/kg. Determine the steam mass flow rate in kg/s.