Ex:-@ Find the END Moment by slope. deflection equation
Q: b) Based on the DoE method, design concrete mix proportions for the following requirements:…
A: Solution: DOE method: design of concrete mix characteristic strength = 45 N/mm2 size of aggregate =…
Q: The control lever is subjected to a clockwise couple of 114 N-m exerted by its shaft at A and is…
A: Asked: To determine the value of distance x, for the given lever. Given: Force (F) = 330 N a = 170…
Q: Find the reactions at the supports A and B.
A: I gave handwritten solution with clean handwriting so please consider my answer.
Q: Q6: Find the stresses on the plane 45 degree shown in and draw Mohr circle and locate OP 120 kPa 45°…
A: step 1-
Q: Obtain the Load Vector: 2 ton/m' L=4 P=10 2EI Lm 3EI 6 m P ton
A: To determine Load vector : Fixed End moments : FAB = 24212=2.67 FBA = -24212=-2.67 FBC =10×62= 30…
Q: A 1000g of sand has been soaked for at least 24hours prior to lab. After drying the sample to…
A:
Q: help! please write the complete solutions. no long explanation needed! upvote will be given!…
A:
Q: The cable exerts a tension of 4 kN on the fixed bracket at A. Write the vector expression for the…
A:
Q: For the state of plane stress (a) constructed Mohr's circle (b) determine the principal 40 MPa.…
A:
Q: A 2.5 inch fire hose discharges a 1.25 inch jet. If the head lost in the nozzle is 6 ft, what gage…
A:
Q: By what factor do you increase the resistance to bending (about y–y axis) if you were to use W460 ×…
A: Draw the schematic diagram of copper tube , Let x be the width and y be the depth of the W460×113…
Q: Two walls in a telecommunications closet should be covered with ________, fire-rated plywood to…
A: Following is required answer :
Q: ain the building properties/configurations whic
A: Building Configuration Shape and environmental factors of any structure plays a very import job in…
Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…
A: Given data w = 11 KN/m L = 5m E = 200 GPA = 2 × 105 N/mm2 I = 115 × 106 mm4
Q: Compute the first three entries in a table for setting out the following vertical curve, at…
A: Length of curve = L L = KA K = 55 A = g1 - g2 = 1.5 + 1.6 = 3.1 L = 55 X 3.1 = 170.5 m
Q: Maximum intensity with respect to the given time.
A: This question is from hydrology and we have to calculate depth and rainfall intensity
Q: horizontal reverse curve is designed for a maximum super speed elevation of 0.12m/m. If the radius…
A:
Q: Describe the content of the GPS broadcast message
A: GPS (Global positioning system) : The Global Positioning System (GPS), formerly known as Navstar…
Q: USE FORCE METHOD. What is the force member AC in the given truss? AE is constant. (kN) Vertical…
A:
Q: The rigid bar ABC is pinned at B and attached to the two vertical rods. Initially, the bar is…
A:
Q: What does cause heat transfer?
A: The creation, utilization, transformation, and interchange of thermal energy (heat) across physical…
Q: 1) A truck and trailer combination having the axle loads as shown in the figure rolls across the…
A: Shear Force: The Algebraic sum of all the vertical forces acting on the beam is known as Shear…
Q: 23. A vertical summit curve have tangent grades of 2.4% and - 3.2%. The required stopping sight…
A:
Q: What is accuracy in measurement? This question is a material science question.
A: *Measurement:- Measurement is important for us to understand the external global, and via tens of…
Q: E. A spiral 80m long connects a tangent with a 7° 30' circular curve. If the stationing of the T.S.…
A: (a) 38.6% (b) 0.03 degree (c) 300 degree (d) 3.422x10-5 m
Q: The combined action of the three forces on the base at O may be obtained by establishing their…
A:
Q: Q2: Wheat is to be grown in a field having a field capacity equal to 27% by weight and the permanent…
A:
Q: Problem I. With the ongoing extension of Manila Skyway, a series of 250 mm diameter circular poles…
A: d = 250mmP at 150mm from centroidal axis = 7.1kNheight of pole = 3munit weight of pole = 22kN/m3…
Q: 3) The overhanging beam supports the loads as shown in the figure. Determine the maximum shear…
A:
Q: Q. 2) Using the Method of Joints: a) Find the force in members GJ, JD, JC, and GC. b) State whether…
A: step 1-
Q: In the truss shown, A =1000 mm², E = 200 GPa and the coefficient of thermal expansion is 12 x10…
A:
Q: Determine the deflection of point A of the beam. Use any method. w A a + a L
A: Let's find out the support reactions For equilibrium of statics (i) ∑MC=0 (CW+ve, ccw-ve) (RB x 2a)…
Q: An L = 33-ft-long soldier beam is used as a key component of an earth retention system at an…
A:
Q: A simply supported beam is loaded as shown below: 8 kN 12 kN 3 kN/m B C 2.0 m 1.0 m. 3.0 m 3.0 m a.…
A:
Q: 1.58 Find the stresses in members BC and BE for the truss shown. The cross-sectional area of each…
A:
Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…
A: Given stresses at the points are SX = 52 Mpa (tensile) Sy = 63 Mpa(tensile) And shear stress Sxy =…
Q: Problem 3. For the truss shown, determine the forces in members AB, BD, AD and CD 400 lb. 200 с S
A:
Q: At fracture, the elongation between the gape marks is 0.12 in. and the minimum diameter is 0.42 in.…
A: limit of proportionality = 59.91 psi modulus of elasticity E =30046 psi yield stress = 68.897 psi…
Q: 20 KN/m -4,5n- AQ 11 1.5-1mx 7 KN.m 9층 B 2n-1.5m2m 10 KN/m 5 KN/m -3m- 5 KN
A:
Q: A rectangular weir is designed to span the full width of a rectangular channel with B=L=2.5 m.…
A: Given, L = B = 2.5 m Q = 0.405 m3/s Cd = 0.625
Q: 1- and the weight are the stabilizing forces in gravity dams. 2- In the empty reservoir conditions,…
A:
Q: Question One Figure Q1 shows a stress state element in a material component. Analyse the element and…
A: Given values: σx=80 MPaσy=-120 MPaζxy=25 MPa The above sign convention was chosen by assuming…
Q: A simple beam AB supports five equally spaced loads P (see figure). Find the reactions at the…
A: Given,L = 36mP = 15 N
Q: shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water…
A:
Q: 116 ft3/s-day. The reservoir routing curves graph is given in Figure 1. Perform calculation until…
A: Given, Spillway crest elevation, H= 50 ft Coefficient, C=3 Spillway length, L=35 ft
Q: Force Method is also know as Method of Answer Displacement
A: methods of analysis of indeterminate structure is done by following methods - 1) Force method /…
Q: Tabulate the components and determine the resultant (magnitude and direction) of the given system of…
A:
Q: , a= 2 m, amd w = 40 kN/m. Use doubl 40 kN/m
A:
Q: In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in…
A:
Q: In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in…
A:
Step by step
Solved in 2 steps
- Determine the deflection at midspan of the structure Group of answer choices (-5wL^4)/384EI (5wL^4)/384EI (wL^3)/24EI (-wL^3)/24EIBefore the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)will rate immediately pls answer asap wc of the ff gives the deflection at point C
- Fixed end support at A and rollers at B and C . A concentrated load of 12 KN at the mid span of BC.Use slope deflection method and constant value of El with E= 200,000 MPa and 1= 400 x 106 mm^4. What is the moment MBC and MABin KN-m? 2 decimal placesDetermine the reactions and moments using the slope-deflection method. reference solution: https://www.bartleby.com/solution-answer/chapter-15-problem-11p-structural-analysis-6th-edition/9781337630931/bb8a9823-94ca-11e9-8385-02ee952b546eSolove deflection at B Use E= 200,000 N/mm2 and 150 mm wide x200 mm high beam - moment area
- DET. THE VALUE OF P THAT WILL CAUSE DEFLECTION OF THE 150X220 mm BEAM EQUAL TO 32mm (AT POINT C) WITH THIS VAIUE OF P , WHAT IS THE DEFLECTION AT POINT B USE E=65 GPaDET. THE VALUE OF P THAT WILL CAUSE DEFLECTION OF THE 150X220 mm BEAM EQUAL TO 32mm (AT POINT C) WITH THIS VAIUE OF P , WHAT IS THE DEFLECTION AT POINT B USE E=656PaCalculate the value of the deflection at point B due to concentrated load P in the form Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
- P1= 100KN A=4The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 0.4 between both collars and the rod determine the maximum supporting force available from friction when F = 0 and when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 618.75answer this: determine the deflection at point D i knm3/EI