Ex. # 5] Pinion 2 in the figure runs at 1 750 rpm and transmits 2.5 kW to idler gear 3. The teeth are cut on the 20° full-depth system and have a module of m= 2.5 mm. Draw the free body diagram of gear 3 and shows all the forces acting upon it. Determine the forces acting upon gear 3. The direction of rotation of gear 3, as shown, is counterclockwise. GIVEN: Figure shown N₂ = 1750 rpm $ = 200 P = 2.5 kW m = 2.5 mm

Ex. # 5] Pinion 2 in the figure runs at 1 750 rpm and transmits 2.5 kW to idler gear 3. The teeth are cut on the 20° full-depth system and have a module of m= 2.5 mm. Draw the free body diagram of gear 3 and shows all the forces acting upon it. Determine the forces acting upon gear 3. The direction of rotation of gear 3, as shown, is counterclockwise. GIVEN: Figure shown N₂ = 1750 rpm $ = 200 P = 2.5 kW m = 2.5 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Similar questions

Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter di= 1.5 in.
In the gear system shown in the figure, the motor applies a torque of 231 N-m to the gear at A. A torque of TC = 440 N-m is removed from the shaft at gear C, and the remaining torque is removed at gear D. Segments (1) and (2) are solid 38-mm-diameter steel (G = 80 GPa) shafts, and the bearings shown allow free rotation of the shaft. Assume DA = 110 mm, DB = 370 mm, L1 = 1.7 m, and L2 = 1.1 m. Calculate the rotation angle of gear D relative to gear B. Express your answer in radian rounded to the nearest thousandths.
A solid constant-diameter circular shaft is subjected to the torques of TA = 560 lb·ft, TB = 1080 lb·ft, TC = 850 lb·ft, and TD = 330 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely.(a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6.(b) If the allowable shear stress in the shaft is 4200 psi, what is the minimum acceptable diameter for the shaft?
3)An ideal set of gears is connected to a cylinder card as shown in the figure. The inertia of the motor shaft in gear G2 is Jm determine:a) inertia JLb) the torque T on the motor shaftc) The transfer function Ω(s)/T(s) (angular speed of the load between the motor shaft)Assume that the friction in the load is BL and the friction in the motor shaft is Bm. Suppose also that the density of the charge disk of ρ
The motor shown in the figure supplies 16.5 kW at 1540 rpm at A. Shafts (1) and (2) are each solid 28 mm diameter shafts. Shaft (1) is made of an aluminum alloy [ G=26 GPa], and shaft (2) is made of bronze [ G=45 GPa]. The shaft lengths are L1=3.3m and L2=2.9m, respectively. Gear B has 56 teeth, and gear C has 97 teeth. The bearings shown permit free rotation of the shafts. Determine: the rotation angle of gear D with respect to flange A. [Answer φD/A = 0.314 rad]
The figure shows the rear rotating axle of a 4-wheel wagon with the same FRONT AXLE design and REAR AXLE design. The wagon moves at a constant speed and the diameter of the wheels carrying the axle is D=512 mm and the circumferential speed=3.1 m/s. Due to the load (m) on the wagon, a force of 16574 Newtons acts in the vertical direction. ALSO, a horizontal force of 21% of the vertical load acts on the wagon laterally (horizontally) in bends. It is planned that the bearings of the axle will be bearing 6008 deep groove ball bearings. Calculate the life of bearing A in hours.The radial effect of lateral loads will not be taken into account in the bearing force calculation. Fo.Fa/Co = 1.38 Pi=3.14
In the fabric dye-printing system given in the figure, the motion is transmitted from the electric motor to the drum of the machine. There is a two-stage reducer in between. Number of teeth of gears z1=17; z2=85; z3=18; z4=72; The efficiency of a pair of gears is given as na=0.97 and the efficiency of each of the gearbox shafts and lower bearing pairs to the drum bearing is given as n=0.97. The diameter of the drum will be D=200 mm, the fabric speed will be v=1 m/s and the pulling force required to activate the band will be taken as F-2000 N. a) Find the number of revolutions of the engine. b) Find the required engine power.
Please draw the figure. Thank you so much.An engine flywheel and a clutch plate are both connected to a transmission shaft. Let the moment of inertia of the flywheel be I1 and its angular velocity ω1, and let the moment of inertia of the clutch plate be I2 and its angular velocity is ω2. The two discs have then been combined by forces which are applied at their axes of rotation so as not to cause any torque. The discs then reached a common final angular velocity after rotational collision. Find the expression for the final angular velocity.
The circular shaft shown (Figure 2) has dimensions D1 = 24 cm , L1 = 6 mm, D2 = 17.5 cm, and L2 = 4 mm with applied torques T1 = 100 kN⋅m and T2 = 40 kN⋅m. The shear modulus is G1 = 60 GPa. Point B is halfway between points A and C. a) Draw the torque diagram for the shaft, using the right-hand rule to determine the correct signs. b) For the given shaft, what is the angle of twist at the free end, point D?
As seen in the figure, a construction machine is rotated by a drive mechanism consisting of belt-pulley and spur gear mechanisms. Engine power P = 5.5 kW ; engine shaft speednm = 1500 rpm ; drive pulley diameter Dt = 16 cm ; diameter of the opposite pulley Dk = 55 cm ; number of pinion teeth z1 = 21 ; number of teeth of the counter gearz2 = 60 ; pulley mechanism efficiency ηk = 0.95 ; Since the efficiency of the gear mechanism is ηd = 0.97: a) Find the output shaft speed nç and the torque Mç on this shaft.b) The force on the taut arm of the belt S1 = 450 N;coefficient of friction μ = 0.3 ; If the winding angle α = 160⁰, is the frictionally transmitted moment Ms sufficient to compensate for the Mg moment on the input shaft? Calculate.
A rack and pinion is a pair of gears that converts rotational motion into translation. As shown in the figure, a torque τ is applied to the shaft. The pinion rotates and causes the rack to translate. The mass moment of inertia of the pinion is I and the mass of the rack is m. Draw the free-body diagram and derive the differential equation of motion
a) A line shaft as shown in Figure Q is driven using a motor placed vertically below it. The pulley on the line shaft is 1.6 m in diameter and has belt tensions 7.5 kN and 2.4 kN on the tight side and slack side of the belt respectively. Both tensions may be assumed to be vertical and the weight of the pulley is negligible. If the pulley is overhang from the shaft, the distance of the centre line of the pulley from the centre line of the bearing being 500 mm.6.Figure Q(i) Predict using distortion energy theory, the appropriate diameter of the shaft that failure will not occur if the yield strength, Sy = 370 Mpa and factor of safety is 2.5. (ii) Assuming the maximum allowable shear stress of 42 MPa, find its diameter using maximum shear stress theory. (iii) Comparing the diameters in (i) and (iii) above, which of them would you have used to design your shaft and why?