Example 101: A hollow steel tube with an insideDiameter of 100 mm must cary a tensile load of 400 kN.Determine the outside diameter of the tube if the stressis limited to 120 MN/m2.Solution 101:

Given data Inside diameter (di) = 100 mm Tensile load (P) = 400 KN Allowable stress = 120 MN/m2

Answered: Example 101: A hollow steel tube with…

Example 101: A hollow steel tube with an inside Diameter of 100 mm must camy a tensile load of 400 kN. Determine the outside diameter of the tube if the stress is limited to 120 MN/m². Solution 101:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Related questions

Q: Problem 3. Determine the outside diameter of a hollow steel tube that will carry a tensile load of…

A: Tensile Stress = force / area

Q: A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine…

A: Given The outside diameter of hollow steel tube is D=138 mm. The inside diameter of tube is d=120…

Q: Ql; A bar ABCD shown in Figure (1) below consists of three sections: AB is of 42 mm diameter and 80…

Q: n the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E=…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given details:Es=205GPaEc=100GPadiameter of rod = 20mm

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

Q: A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile…

Q: Fill in the blanks: A hollow cylindrical column is placed on a steel plate on a concrete pedestal,…

A: Given:P=750 kN55=MPado=25 cm =250 mm

Q: (Q1) A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of…

Q: Example (13) A load of 300kN is supported by a short concrete column of size 250mm square. The…

Q: Find the maximum stress induced in the following cases taking stress concentration into account: 1.…

Q: An aluminum rod length of 1.0 m and cross-secrional area 0.0005 m2 is used to support a load of…

A: Calculated stress on the aluminum rod. length of 1.0 m and cross-secrional area 0.0005 m2 is used to…

Q: A bracket is designed with a pin-pin horizontal tie rod supporting a boom that is also pinned at two…

A: Given data as per question vertical load =6 KN Tensile yield strength =400 Mpa Considering FBD of…

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

Q: 100 kN lsize as sho 80 [A find the diameter of the rivet. 18. A bracket in the form of a plate is…

A: Given Load= 100 kN Maximum shear stress = 70 MPa Cursing stress = 100 MPa To find Diameter…

Q: A cantilever beam, 100 mm wide by 270 mm high and 9 m long, carries a load that varies uniformly…

A: Given:b=100 mmd=270 mmL=9 mW=1300 N/m

Q: 5. A load of 5 kN is to be raised by means of a steel wire. Find the minimum diameter required, if…

A: Given data: F=5 kNσ=100 N/mm2 Need to determine the minimum required diameter of the wire.

Q: Figure shows a tie bar made of steel. When bolted between A and B double brackets, it is to be…

A: Given Data, P= Tensile load in the bar = 100 KN The bolt is of double brackets, so the shear load…

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of…

A: To find: The load carried by the steel rod and the brass bush and the compressive stress set up in…

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

Q: Problem no. 1 A rectangular post which is made up of two blocks of wood glued together along a joint…

A: Given: The shear and normal stresses in glue are 21755.7 psi and 17404.5 psi respectively. Axial…

Q: A cantilever beam, 80 mm wide by 270O mm high and 8 m long, carries a load that varies uniformly…

A: Draw a diagram for the cantilever beam. Here, w1 is the load intensity at point B i.e. at 5 m from…

Q: 41.) A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is…

Q: A Portable Crane will be designed as shown in Figure which is able to withstand dynamic loads. The…

Q: A 5-m high aluminum cylinder must support a load of 450 kN. If the maximum allowable stress is 0.14…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a…

Q: Example 18.1. A short C.I. column of hollow circular section is attached with a projection bracket…

Q: A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN.…

A: GivenD=25 mm=0.025md=12 mm=0.012mF=40 kN=40×103 Nσmax=225 MN/m2=225 ×106 N/mAskedσ=?Fmax=?

Q: Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given data: As the diameter of each rod is the same, so the cross-section area will be also the…

Q: Two hollow circular rods are welded together at B and loaded as shown in Figure 5. Load Pi acting at…

Q: A scuba tank is being designed for an internal pressure of 2,685 psi with a factor of safety of 2.0…

Q: Problem 907 Determine the largest load P that can be supported by the circular steel bracket shown…

A: Given data :- diameter of section A-B = 100 mm normal stress = 80 Mpa find the largest load P that…

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of…

Q: 1.5 Figure 1.9 shows a circular steel rod of length 40 m and diameter 8 mm, which hangs in a mine…

Q: PCS Problem 101: Tensile and Compressive Stresses The members of the truss are 25mmx50mm in cross…

Q: Example 101: A hollow steel tube with an inside Diameter of 100 mm must carnry a tensile load of 400…

Q: Problem 1: Figure MEC – 124, shows a uniform cylinder with a diameter of 1.5 m supported by a bar AB…

Q: Example 3.8. A lever is keyed to a shaft of 100 mm diameter. The width of the key is 12 mm and the…

Q: Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction,…

A: Given data :- Length = 100 mm Width = 50 mm Thickness = 10 mm Tensile load = 10 KN

Q: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a…

Q: An axial bar fixed at both ends with no loads applied is subjected to an increase of temperature.…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Example 101: A hollow steel tube with an inside
Diameter of 100 mm must cary a tensile load of 400 kN.
Determine the outside diameter of the tube if the stress
is limited to 120 MN/m2.
Solution 101:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.