A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What force is required to punch a square hole (25-mm*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN m2. Purcher 30 mm

A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What force is required to punch a square hole (25-mm*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN m2. Purcher 30 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5 decimal places 32. Two identical plates of 61 mm wide and 6 mm thick is connected by a square pin with side dimension 14 mm. If a plate is subjected to a tensile force of 29 kN, determine the maximum tensile stress (MPa) developed in the plate
Kindly give right answer other wise don't attempt Determine the maximum stress produced in a rectangular plate 50 mm wide, 8 mm thick with a central hole of 10 mm. It is loaded in an axial tension of 1 kN. Answer-7.813N/MM2
From the given bracket shown, which consist of two plates riveted to the column by 4-22mm Ø rivets which is subjected to an eccentric load of 150 kN. 1. Which of the following gives the shearing stress due to axial load only? a. 49.325 MPa b. 70.25 MPa c. 80.47 MPa d. 68.25 MPa 2.. Which of the following gives the shearing stress due to moment alone? a. 69.76 MPa b. 70.94 MPa c. 56.39 MPa d. 64.32 MPa 3. Which of the following gives the maximum shearing stress? a. 110.30 MPa b. 120.40 MPa c. 140.50 MPa d. 105.70 MPa
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm
PLS ANSWER ASAP TY! For the assembly shown, a yoke on a 30 mm diameter rod is attached to a 25 mm thick bracket via 15 mm diameter bolt as shown. The ultimate axial strength in the 30 mm dia. rod is 150 MPa. a)Determine the largest load P (in KN) that can be applied to the rod if a factor of safety of 2.5 with respect to the ultimate axial strength is required. b) What is the tensile axial stress on the rod (in MPa)? c) What is the shear stress on the bolt (in MPa)? d) What is the factor of safety for the 15 mm. dia. bolt with respect to the ultimate shear strength? (in 2 decimal places)
The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.
a) A hole is to be drilled in the plate at A. The diameters of the bits available to drillthe hole range from 12 to 24 mm in 3-mm increments. Determine the diameterd of the largest bit that can be used if the allowable load at the hole is to exceedthat at the fillets.b) If the allowable stress in the plate is 145 MPa, what is the correspondingallowable load P?
If the principal stresses are of opposite signs, then failure occurs in the plane. True or false?
5 decimal places 1. Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it developed a stress of 21 MPa. Take note that the inner diameter is 3/6 of the outer diameter. 2. Three identical plates of 67 mm wide and 7 mm thick is connected by a square pin with side dimension 17 mm. If the middle plate is subjected to a tensile force of 25 kN, determine the shear stress (MPa) developed in the pin. 3. Two identical plates of 61 mm wide and 5 mm thick is connected by a square pin with side dimension 19 mm. If a plate is subjected to a tensile force of 28 kN, determine the bearing stress (MPa) developed in the plate.
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
A rectangular piece of wood, 55 mm by 101 mm in cross-section is used as a compression block. The grain makes an angle of 20 degrees with the crosssection plane. Determine the maximum axial load (kN) that can be applied to the block if the allowable shearing parallel to the grain is 5 Mpa. What is the allowable compressive stress(Mpa) parallel to the grain if the failure on shearing and compression is to occur simultaneously?
The axial load 229kN applied to the lap joint is distributed equally among the three 17.1-mm-diameter rivets. What is the maximum tensile stress (in Mpa) in the plate if w=139.6mm and t=29mm? Round off the final answer to three decimal places.