Example 14 The uniform circular disk has a mass of 7.6 kg and a radius of 0.6m The disk is suspended from a pin at A and can rotate freely about A. The pin is connected to a horizontal plate on smail wheels. At the instant t = 0 a force is applied to the plate (which is initially at rest), so that it accelerates at a 1.5 m/s² (towards the right). Now calculate the horizontal and vertical components of the reaction at A and the magnitude of angular acceleration of the plate at the instant t = Os. A2 2009 Question 6 L. 106 ANSWER: Ax= 3.8 N A₂ = 74.6 N a = 1.67 rad/s²

Example 14 The uniform circular disk has a mass of 7.6 kg and a radius of 0.6m The disk is suspended from a pin at A and can rotate freely about A. The pin is connected to a horizontal plate on smail wheels. At the instant t = 0 a force is applied to the plate (which is initially at rest), so that it accelerates at a 1.5 m/s² (towards the right). Now calculate the horizontal and vertical components of the reaction at A and the magnitude of angular acceleration of the plate at the instant t = Os. A2 2009 Question 6 L. 106 ANSWER: Ax= 3.8 N A₂ = 74.6 N a = 1.67 rad/s²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A prop shaft of a heavy-duty truck has two bearings which are positioned at 3 metres from each other. The shaft must rotate at 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of (MA = 10 kg) and (MB = 5 kg) acting at the extremities of the arms 0.45 m and 0.6 m long,respectively. The planes in which these masses rotate are 1.2 m and 2.4 mrespectively, from the left end bearing supporting the shaft. The angle between the arms is 60°. If the masses are balanced by two counter-masses (named X and Y) rotating with the shaft acting at a radius of 0.3 m and placed at 0.3 m from each bearing centre:2.1. Draw a diagram illustrating the position of masses on the shaft. 2.2. Calculate the dynamic force in Newtons. Tabulate the results. 2.3. Calculate the moment acting on the shaft in Newton-metre. Tabulate the results.
A particle of mass 0.102 kg is rotating at 840 rpm at a radius of 135 mm. At t=2 the radius begins to expand at a rate of 14 mm.s-1. What is the radial force at t=1.9s [N] What is the arc length traveled by the mass at t=1.9 s? [m] What is the transverse force on the mass at t=4s? [N]
A solid spare, a solid disk, and a thin hoop are all released from rest at the top of the incline (ho = 20.0 cm). a) without doing any calculations, decide which object would be spinning the fastest when it gets to the bottom. (Explain) b) again, without doing any calculations, decide which object would get to the bottom first. (Which one has greater translational speed?) think CoE. c) assuming all objects are rolling without slipping, have a mass of 2.00 kg and a radius of 3.00 cm, find the rotational and translational speed at the bottom of the incline of any one of these three objects.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block. NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
A prop shaft of a heavy-duty truck has two bearings which are positioned at 3 metres from each other. The shaft must rotate at 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of (MA = 10 kg) and (MB = 5 kg) acting at the extremities of the arms 0.45 m and 0.6 m long, respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively, from the left end bearing supporting the shaft. The angle between the arms is 60°. If the masses are balanced by two counter-masses (named X and Y) rotating with the shaft acting at a radius of 0.3 m and placed at 0.3 m from each bearing centre:
Blocks A and B shown in the figure have masses of 5 kg and 10 kg respectively.If the pulley is treated as a 3 kg solid disk with a 15 cm radius, determine the acceleration of the block A. Disregard the rope mass and any slip on the pulley.Consider that the moment of inertia of the pulley is given by Ip = (1/2)mr² in which m is the mass of the pulley and r is of radius the pulley.
A hoop of radius 95mm and mass 100g is rotated via a capacitor driven power source with P(t)=1.61e-1.3tW. (since it is a hoop, it is a special case, and r=rG) Assuming the hoop is accelerated from rest, determine the rotational velocity after t=8.5s. [rad.s-1] Determine the rotational speed of the hoop after t=8.5s if the power source acts to roll the particle from rest on a horizontal surface. [rad.s-1]
Asubject of mass 65 kg has her gait analyzed. Suppose that the x componentof the force measured by a force plate takes the shape shown in Fig. (a) If the forward velocity of the walker is 2 m/s at heel strike, what is it0.4 s after heel strike?(b) Estimate the corresponding change in height for the subject’s center ofgravity (i.e., from heel strike to 0.4 s later).
A uniform cylindrical turntable of radius 1.9 m and mass 30.0kg rotates counterclockwise in a horizontal plane with an initial angular speed of 4pi rad/s. The fixed turntable bearing is frictionless. A lump of clay of mass 2.25kg and negligible size is dropped onto the turntable from a small distance above it and immediately sticks to the turntable at a point 1.80m to the east of the axis. A. Find the final angular speed of the clay and turntable. B. Is the mechanical energy of the turntable-clay system constant in this process? C. Is the momentum of the system constant in this process? Explain your answer.
Hi there, could I please have some help solving the question below. Thank you very much in advance. A particle of mass 4.9 kg is traveling on a constant 8.7m radius with a tangential speed of 1.4e-0.125t m.s-1. 1. Determine the rotational speed of the mass at t=2.6 seconds. 2. Determine the tangential force at t=2.6 seconds. 3. Determine the normal force at t=2.6 seconds.
A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the extremities of the arms 0.45 m and 0.6 m long respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively from the left end bearing supporting the shaft. The angle between the arms is 60°. The speed of rotation of the shaft is 200 r.p.m. If the masses are balanced by two counter-masses rotating with the shaft acting at radii of 0.3 m and placed at 0.3 m from each bearing centers, estimate the magnitude of the two balance masses and their orientation with respect to the X-axis, i.e. mass of 10 kg ‎‏Note: It must be solved using the graphic method, not the equations method.
A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the extremities of the arms 0.45 m and 0.6 m long respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively from the left end bearing supporting the shaft. The angle between the arms is 60°. The speed of rotation of the shaft is 200 r.p.m. If the masses are balanced by two counter-masses rotating with the shaft acting at radii of 0.3 m and placed at 0.3 m from each bearing centers, estimate the magnitude of the two balance masses and their orientation with respect to the X-axis, i.e. mass of 10 kg.