EXAMPLE 3–3 Volume and Energy Change during Evaporation XAMPLE 3-3 Volume and Energy Change during Evaporation A mass of 200 g of saturated liquid water is completely vaporized at a con- stant pressure of 100 kPa. Determine (a) the volume change and (b) the amount of energy transferred to the water.

EXAMPLE 3–3 Volume and Energy Change during Evaporation XAMPLE 3-3 Volume and Energy Change during Evaporation A mass of 200 g of saturated liquid water is completely vaporized at a con- stant pressure of 100 kPa. Determine (a) the volume change and (b) the amount of energy transferred to the water.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.3P

See similar textbooks

Similar questions

At a constant pressure, how does a volume of gas vary with respect to the absolute temperature?
A 0.5-m3 vessel contains 10 kg of refrigerant-134a at -20 °C. Determine (a) the pressure, (b) the total internal energy, and (c) the volume occupied by the liquid phase.
Which is higher for gases, specific heat in constant volume or specific heat in constant pressure? Explain why.
The specific volume of water at 30 psia and 250.34 F (saturation) is 0.017004 cubic feet per pound mass. How much heat in Btu/hr must be added to evaporate the water at the rate of 10 gal/hour if the latent heat of vaporization is 945.9 Btu per pound mass
An insulated piston-cylinder device contains 4.5 m3 of water with a quality equal to 0.5 at aconstant pressure of 300 kPa. Water is stirred by a paddle wheel while electrical current flowsthrough a resistor placed in the water. During this constant-pressure process, the paddle wheelwork amounted to 1000 kJ and electrical work from the resistor amounted to 19000 kJ. What isthe temperature of the water in its final state? Show the process on a P-v diagram with respectto saturation lines.
A piston-cylinder device initially contains 300 liters of of water at 430 kPaa and 110 degC. Heat is added to the water at constant pressure until the liquid is entirely vaporize.Determine (a) the amount of heat added
Water at 15 °C and 1 atm pressure is heated to 95 °C at constant pressure. Using coefficient of volume expansion data and assuming β at average temperature, determine the change in density of water in kg/m3. (Use table of property for saturated steam in Fluid Properties – II lecture material.)
Calculate ∆U in KJ for 0.5 Kg water when it vaporized at the constant temperature of 100ᴼC and constant pressure of 101.33 KPa. The specific volumes of liquid and vapor water at these conditions are 0.001 and 1.673 m3/kg respectively. For this change, heat in the amount of 3256.9 KJ is added to the water.
A rigid tank of volume 0.6 m3 contains saturated R-134a vapor at 24°C. The contents are cooled until the temperature is O°c. How much heat is removed? Show the process on a P-v diagram.
A 0.05 kg vessel contains 4 kg of refrigerant-134a at a pressure of 180 kPa. Determine (a) the temperature (b) the quality (c) the enthalpy of the refrigerant (d) the volume occupied by the vapor phase.
why water evaporates at constant pressure at constant temperature, and how the temperature is when the pressure is different?
A steam boiler was found to have a factor of evaporation of 1.75 producing 2250 kg/hr of steam. If the fuel consumption of this boiler is at 3.75 kg/min, determine the equivalent specific evaporation.