Example 4.2.5: Turning tool made of HSS used in the long process of turning shaft of aluminum alloy with the length of 300 mm, diameter of 70mm, the speed of rotation is 364 rpm. Feed of 0.01 mm/rev, angle of curved cutting edge 21°. age of cutting edge contrast 114min for cutting speed of 50mm/min. Calculate the age of the cutting edge and how many times the tool need to be sharpened.

Example 4.2.5: Turning tool made of HSS used in the long process of turning shaft of aluminum alloy with the length of 300 mm, diameter of 70mm, the speed of rotation is 364 rpm. Feed of 0.01 mm/rev, angle of curved cutting edge 21°. age of cutting edge contrast 114min for cutting speed of 50mm/min. Calculate the age of the cutting edge and how many times the tool need to be sharpened.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate:
Suppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.
A slab milling operation is performed on the top surface of a tool-steel workpiece 450 mm long by 7.5 cm wide. The helical milling cutter, which has an 80 mm diameter and seven teeth, is set up to overhang the width of the part on both sides. Cutting speed is 4000 mm/min, feed is 0.015 cm/tooth, and depth of cut = 0.60 cm. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.05 m is added at the beginning of the pass, and an overtravel distance at the end of the pass equal to the cutter radius plus 0.0115 cm, what is the duration of the feed motion
Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by using a carbide insert. If the approach length and over run length is taken as 5 mm, Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
A steel rod 250 mm long and 200 mm in diameter is being reduced to 190 mm in diameter all over its length in one travel. The machine spindle rotates at 500 rpm, whereas the tool is moving at an axial feed of 0.5 mm/rev; calculate the following: Material removal rate (mm3/min) Consumed gross power in Nm/s if cutting force is 477.5N and mechanical efficiency is 90% Cutting time plzz complete in 30 minutes
11. Estimate the machining time required to rough turn a 0.5 m long annealed copper alloyRound bar from a 60 mm diameter to a 58 mm diameter, using a high-speed tool. Estimate the time required for an uncoated carbide tool.
In orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the main cutting force is 1000 N and the feed force is 800 N. The shear angle is 25° and orthogonal rake angle is zero Employing Merchant's theory, what is the ratio of friction force to normal force acting on the cutting tool?
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
A motorised metal guillotine machine is required to cut 45 mm diameter hole ina plate of 20 mm thickness at rate of 35 holes per minute. It requires a torqueof 7 Nm for an area of hole in mm?. If the cutting takes 1/10 of a second andthe speed of its flywheel varies from 165 rpm to 145 rpm, calculate:1.Energy required to cut a hole.2.Energy required for cutting work per second.3.Maximum fluctuation of energy of the flywheel.4.Mass of the flywheel having radius of gyration of 1.5 m.
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy= 1200 ksi. If the width of cut is 0.30 in. and the student set a rake angle of 0° and a cutting speed of 200 ft/ min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
Draw the forces and angles involved in the cutting process and calculate shear angle (0), friction coefficient and tangential force if ,cutting force = 80 kN, resultant of forces =100kN, friction force=75kN, rake angle =20° undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mm
A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiece having a feedrate of 0.1 mm/tooth and a depth of cut of 4.0 mm. The cutter of 50 mm diameter has 18 straight teeth and rotates at 135 rpm. The given specific energy for this material is 3.5 W s/mm3 and the slab mill is wider than the workpiece to be machined. Calculate:‧ the material-removal rate;‧ the power and torque required for this operation;‧ the cutting time. (243 mm/min, 77760 mm3/min, 4.5 kW, 52.8 s)