• Example A Cu rod of length 4 m with uniform cross-sectional area hangs freely and vertically from the ceiling of a building at one end. If the diameter is 1 cm, draw a free body diagram of the rod and use it to find the deformation in the rod as result of its own weight. Cu: E=120 GPa, p=8910 kg/m3, g39.81 m/s

• Example A Cu rod of length 4 m with uniform cross-sectional area hangs freely and vertically from the ceiling of a building at one end. If the diameter is 1 cm, draw a free body diagram of the rod and use it to find the deformation in the rod as result of its own weight. Cu: E=120 GPa, p=8910 kg/m3, g39.81 m/s

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.18P: A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed...

See similar textbooks

Similar questions

A shaft having length equal to 10 m and diameter equal to (50+ 16) mm is simply supported at both ends. The shaft carries four masses (150 + 16) kg, (200 + 16) kg, (250 + 16) kg and (300 + 16) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A shaft having length equal to 10 m and diameter equal to (50+ 01) mm is simply supported at both ends. The shatt carries four masses (150 + 01) kg, (200 + 01) kg, (250 +01) kg and (300 + 01) kg. These masses are located at a distance of 1.5m, 2.5 m, 5.5 mand 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m? and mass density for the shaft material is 7500 kg/m?3. Determine critical speed of the shaft in revolutions per minute for the following two cases: 1. Effect of the mass of the shaft is neglected. 2. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A vertical shaft 25 mm diameter and 0.75 m long is mounted in long bearings and carries a pulleyof mass 10 kg midway between the bearings. The centre of pulley is 0.5 mm from the axis of theshaft. Find (a) the whirling speed, and (b) the bending stress in the shaft, when it is rotating at 1700r.p.m. Neglect the mass of the shaft and E = 200 GN/m2.
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
To get up on the roof, a person (mass 72.0 kg) places a 6.80 m aluminum ladder (mass 13.0 kg) against the house on a concrete pad with the base of the ladder 2.00 m from the house. The top of the ladder rests against a plastic rain gutter, which we can assume to be frictionless. The center of mass of the ladder is 2.00 m from the base, as measured along the ladder. The person is standing on the ladder 3.00 m from the base, as measured along the ladder. Find the normal reaction and friction forces (in N) on the ladder at its base. (Enter the magnitudes.)
A round, prismatic steel bar (E = 210 GPa) of length L = 2000 mm and diameter d = 15 mm hangs vertically from a support at its upper end (Figure on right). A sliding collar of weight W drops from a height h = 150 mm onto the flange at the lower end of the bar without rebounding. Assume W is given in Newton by W = 289. Calculate the maximum elongation of the bar due to the impact.
You open a restaurantand hope to entice customers byhanging out a sign (Fig. ).The uniform horizontal beam supportingthe sign is 1.50 m long, hasa mass of 16.0 kg, and is hingedto the wall. The sign itself is uniformwith a mass of 28.0 kg andoverall length of 1.20 m. The twowires supporting the sign are each32.0 cm long, are 90.0 cm apart,and are equally spaced from themiddle of the sign. The cable supportingthe beam is 2.00 m long.(a) What minimum tension mustyour cable be able to support without having your sign come crashingdown? (b) What minimum vertical force must the hinge be able to supportwithout pulling out of the wall?
A shaft having length equal to 10 m and diameter equal to 70mm is simply supported at both ends. The shaft carries four masses 170 kg, 220 kg, 270kg and 320 kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
In the figure, a shaft rotating with constant angular velocity and connected to this shaft at a distance of r1=136 cm, r2=49 cm, r3=69 cm and r4=61 cm m1=3.3 kg, m2=1.6 kg, m3=8.9 The point masses of kg and m4=10 kg are seen. Find the position of the counterweight in degrees, with rd=90 cm. (θ1=63˚, θ2=138˚, θ3=260˚, θ4=234˚)
The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter is filled with a liquid (SG>1, like glycerin) and the ret with water. The tank is now rotated about its vertical axis at constant angular speed w. Determine the value of angular speed in rad/s when point P on the axis at the liquid-liquid interface touches the bottom of the tank. Include the free body diagram in your solution. a.12.1 b.10.3 c.14.4 d.13.2
A steel bar of uniform cross section is 2 m long and has a mass of 25 kg. The bar is supported in a vertical position by a horizontal pin at the top end of the bar. Determine the work done on the bar by gravity as the bar rotates 60° about the pin in a vertical plane.
Which spring, the truncated cone spring or the helical spring, would have a larger spring constant? Explain.